Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
David S - August 13, 2022
Verified Purchase
Worked fine couple wires different but was able to fonfigure
Part was great condition.
★★★★★
★★★★★
Betty D - May 24, 2020
Verified Purchase
Wrong part for stove top
Hi, we need to send it back, think it may not be the right one.
Thanks
BEtty D
★★★★★
★★★★★
Mark S - January 15, 2019
Verified Purchase
Part ok, install a little challenging
Got the part quickly and followed one of the other reviewers instructions to install. One issue I encountered was that the markings for the electrical connections were not identical to the old switch - I recall there are 5 connections, 4 had the same label but one was different - so I just connected the ones that were the same and the leftover went to the last open terminal. Suggest checking this before you remove the original switch and wires, just in case.
In addition, the wiring on my cooktop didn't have enough slack to connect the switch, then install it to the cooktop. This will probably vary from appliance to appliance, but it's worth considering installing the switch to the cooktop first, then route and connect the wires.
Overall satisfied with the part and service.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 10 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Main burner (right front) always on high
Turn off breaker. Lift cook top from counter. Remove perimeter screws from glass cook top and remove glass. Remove screws attaching control. Replace control and leads. Note: 4 of 5 lead attachment marking points matched old control - I had to guess the fifth. "P" on old was attached to "PC" on new. Attachment poi
... Read morents on new were configured differently from old. The leads were just barely long enough to reach. Replaced perimeter screws and cooktop.
Read less
Rick from STATE COLLEGE, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large right front burner would go to high without turning the temp up.
1. Turned of circuit breaker to stove. 2. Take two screws out of control panel, and lifted it up. 3. Lay panel on side and removed knob. 4. Flipped panel over and take several pic for reference of each wire and location on back of controller. 5, Flipped panel back over and take needle-nose players and unhooke
... Read mored each wire tab on back of controller. 6. Flipped panel back over and take two screws out that hold controller on front of panel. 7. Flip the panel back over and remove the old controller. 8. Position the new controller in the panel and install the the two screws back to secure it to the panel. 9. Attach wires back to new controller based on your pic taken. Verify correct location to pic. 10. Attached panel on back of stove. Make sure all wires are secured inside of the control panel. 11. Turn circuit breaker back on and verify the burner is working correctly.
Read less
Fred from DAMON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replacement of switch WB23K5052 with switch WB24X29364
Remove ten screws that attach top then remove top. Remove four screws holding switches in place and lift for access. remove two screws from switch. Record wire color for positions P L1 L2 for proper positioning on replacement switch. One wire was to short so had to make a two inch extension to complete the hookup. Reassemble and the
... Read moreburners work as original.
Read less
Jim from GREENSBORO, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element temp would not reduce
Remove stove top from cabinet. surf for you tube videos to replace switch.
William from BUCKHEAD, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Uncontrollable temperature high setting only
Turn off breaker removed cooktop from countertop . Removed Phillips screws remove glass top .Remove two screws holding switch & reinstalled
james from BRANCHBURG, NJ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cook top burner stayed on high
using the info on this site i guessed it was the switch. It was. this is a Radiant Heat in counter drop on cook top. i was nervous about getting it out of the counter but that was eassy, just sits on top. the One issue was diconnecting the BX electric cable from the elecric box. mine did not have threads and a nut. but a push in fitting w
... Read moreith small tabs.. i forced it out by pushing the tabs in with a screw driver.. later found out it was a band that was eassily removable by just prying it open with a screw driver... and later replacing it.. the glas removal was just screws and the switch was insised a cover with four screws.. plugged the new one in (careful to keep the connections the same, and reversed the process.. ready to fix it again if needed!thanks for having the part... probably saved $200! can take less than 30 minutes if you get past the electric connection quicker than i did... that;s it!
Read less
Roy from Yardley, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
11 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dual heating burner was always on High regardless of control; setting
Removed unit from counter top. Opened to locate wiring diagram. Identified part snd searched on internet. PartSelect.com provided all missing information and had easy to follow instructions...confirming my initial assessment of the problem. Ordering was easy; delivery fast. Job completed.
Carl from Punta Gorda, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cooktop Switch broke, burner would not come on.
1) SHUT OFF POWER 2) Removed the cooktop from the counter 3)Remove 6 screws holding the cooktop glass frame to the housing 4)Removed 4 screws holding the switch retainer to the housing 5)Removed 2 screws holding the switch in place 6)Moved one wire at a time from the old switch to the new switch 7)Reassembled
David from New Bremen, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
7 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cooktop Burner was always on High no matter what the setting on the Control
1) Turn Power off at Circuit Breaker 2) Lift Cooktop out of counter top. 3) Remove all dials from controls by pulling straight up. 4) Remover glass plate which covers burners by removing screws along outer edge. 5) Remove the two top screws from the control to be replaced (this holds the infinite contr
... Read moreol to bracket) 6) Remove one wire at a time from the old control and plug on the new one in correct orientation. 7) Reverse above order to reassemble.
(Note: Not all infinite controls are same PN when ordering, the drawingings are deceiving that they are)
Read less
Raymond from Salt Point, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
32 of 41 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch had lost infinite control.
Removed counter top stove, released zip ties on flex conduit,removed cover glass, removed switch anchor panel, removed old switch,(noting the color of each wire) replaced switch reassembled.
Fielding from Bulverde, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
11 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steve
October 17, 2019
Diagram shows 4 ea. How many come in the package for $48.Xx?
For model number JP3432S3BG
Hi Steve, this includes 1 per package. Thank you for your question and good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
October 17, 2019
Range symptoms: Inconsistent heating. Sometimes when the eyes are turned down on low, it will all of a sudden heat up and cause whatever is cooking to boil over. Could this part be the problem?Does this part fit the model # stated above?
For model number JP3432S3BG
Hi Steve, the switch could definitively be the problem as they help control the burners. This part is fully compatible with your model. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tony
December 27, 2019
GE profile radiant cooktop 30". Need new switch to control large burner/element. Cannot find my model number on your site. Model # is either jp930woa1ww, or jp930w0a1ww.
For model number JP930WOA1WW
Good Day Tony. Thank you for your question in regards to your unit. The model number you provided is not recognized. Please verify the number you provided us. If it is correct, we recommend contacting the manufacturer and seeing if they could provide you with a part number, and then you are always welcome to check back to see if we carry the part! Best Regards.
Was this helpful?
Thank you for voting!
Stuart
December 1, 2022
The upper left burner (6 inch) doesn’t work and the selector switch seems to be the problem. Instead of “snapping” between settings from low to high, it just spins and feels loose. Are the selectors switches burner-specific or universal? Not sure what
“infinite control” means.
Also, the “surface hot” indicator light stays on constantly, even if cooktop hasn’t been used. What parts do I need? Thanks!
For model number JP660WV1WW Cooktop
Hello Stuart, thank you for getting in touch. According to our research, we would recommend checking the following parts to fix your issue: selector switch, part number PS237199, infinite control switch, part number PS12342205, and element, part number PS243901. The switches are sometimes burner specific and sometimes universal. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
