Note: Wiring could differ from original, will possibly need to be installed by an appliance repairperson.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Range.
This part works with the following products:
General Electric.
Part# WB27T10416 replaces these:
AP3205899, 963830
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Lori F - July 2, 2021
Verified Purchase
Don't be intimidated, this is easy and YOU can do it!
Step 1) Unplug the appliance and take the screws out.
Step2) Take a close-up photo of the existing wiring inputs on the board.
Step 3) Unplug all the connectors or take one out at a time and put it on the new board.
Step 4) When you put the ribbon in, make sure you hear it click before closing the tabs.
Step 5) Screw it all back together, plug it in and set the clock.
It really is THAT easy!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Buttons stopped working on the keypad.
Everybody said the Electronic clock oven control needed to be replaced, not the keypad. It was the keypad. Unpluged the range. Pulled the 4 burner control knobs off, Unscrewed the 4 burner contol knob bottoms to remove the panel cover, removed 2 of the keypad screws an loosened the other 2. Removed 4 screws holding the oven control pan
... Read moreel. Turned the panel over to access the keypad wiring ribbon. Released the ribbon, turned the panel over to remove the old keypad. Put the new keypad ribbon through the panel and pushed the ribbon into the ribbon slot, put the anel beck in place with 4 screws, slipped the keypad in place on 2 loosened screws. put the remaining 2 screws back in. tightened all four screws. replace the control panel cover and knobs. Plug back in and viola.
Oven would intermittently loose all power when hot
First found and threw appropriate breakers. Then removed knobs and faceplate retainer nuts and pulled off faceplate. Next removed four control panel retaining screws and lifted out and partially spun/inverted control panel. Couldn't fully remove due to wiring. Next removed four oven control screws and pulled back control module. Then just
... Read more removed all wiring connections to old control module. Worked in reverse with new control module, turned breaker back on, and just had to set the clock. Back in business!
Read less
Eric from Hemphill, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Felicia
July 1, 2019
My oven and clock is out. Nothing dont work but the 4 cookers.
Hello Felicia, thank you for writing. It sounds like the Electronic Control Board needs to be replaced, but we will need the model number for the appliance to locate the correct replacement for it. We look forward to hearing back from you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michael
February 15, 2018
None of the burners or oven elements heat it has power because the lights on the panel come on but no heat happens . Could it be the electronic clock oven control panel?
For model number JSP42SN2SS
Hi Michael,
Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check with a multimeter. You will need to test the sensor with a multimeter and the sensor should be at room temperature. You will need to measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
William
June 27, 2019
I changed out the keypad module today (everything worked on the original but 3 and 4). Turned power back on and everything worked perfectly! My wife put some food in the oven on 400 degrees and the display started flashing and now "locked door" is illuminated on the display panel and nothing will work. Any ideas?
For model number JDP47F4WW
Hello William, thank you for inquiring. Try disconnecting the power to the range for 30 seconds. Reconnect the power and see if the door will unlatch. If it does not, set the oven to clean for 1-2 hours and then wait 30 minutes for the oven to cool and try unlocking it then. We hope this helps.
Was this helpful?
Thank you for voting!
David
July 13, 2021
I need to solve the fault code f0, is this the part I need ?Thanks
For model number JSP47WF6WW
Hello David, Thank you for the question. According to GE the F0 error code indicates a button on the touchpad is either stuck or short-circuited and the Touch Pad, PartSelect Number PS2353587 will need to be replaced. We hope this helps!
The oven comes on then heats up the display shows temp then it shut off and display does not show temp but the time still is shown
For model number JD630DF1BB
Hello Judd, thank you for contacting us. The most probable cause of the issue is a faulty oven sensor, part number PS236398, and the control board, part number PS753786. These parts monitor the temperature and control the oven heat. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Cook top burners work, but the oven doesn't, nothing works on the touch screen pad and has error message on it that states bad Line.
For model number JD630STSS
Hi Todd, thank you for writing in. Bad Line indicates that the Electronic Control Board has failed and should be replaced. We hope this helps.
Was this helpful?
Thank you for voting!
John
January 1, 2024
HAVE A F7 CODE,,, WHAT DO I NEED TO DO
For model number PD900DP3WW
Hi John, thank you for contacting us. According to our research, the F7 code indicates that there is a problem with the key panel. You may need to replace the key panel support assembly, part number PS2370119, to fix the issue. We hope this solves your problem!
