Cooktop Wire Plugs and Connectors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Cooktop Wire Plugs and Connectors
Your Price
$16.24
In Stock
Cooktop Terminal Block Kit
As far as the drawer glides they just snap into place Read more...
PartSelect Number PS470125
Manufacturer Part Number 5303935058
This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.
Fixes these symptoms
- Element will not heat
- Oven not heating evenly
- Will Not Start
- See more...
Installation Instructions
Steven from Taylors, SC
rental property stove only had 2 working burners and bottom drawer off track
first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case. As far as the drawer glides they just snap into place Read more...
Your Price
$9.37
In Stock
Cooktop Main Terminal Block Kit
PartSelect Number PS471605
Manufacturer Part Number 5304409888
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Timothy from Spring Valley, AL
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read more...
Your Price
$13.91
In Stock
Cooktop Surface Burner Receptacle Kit
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com. Read more...
PartSelect Number PS1570190
Manufacturer Part Number 12001676
The tools you will need to replace the surface burner receptacle kit on your range include a Phillips screw driver, and a pair of wire strippers. Before doing this repair, make sure to disconnect your appliance from the power supply and wear work gloves to protect your hands. The surface burner receptacle kit comes with a plastic block, high temperature wire nuts, a metal bracket, and wires. This part functions as the connection between the wire harness and the surface element in your range.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Richard from Carthage, NC
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com. Read more...
Your Price
$13.42
In Stock
Cooktop Surface Burner Plug-In Block Kit
I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon Read more...
PartSelect Number PS340571
Manufacturer Part Number 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Jon from Oakley, CA
Surface elements quit working
Drilled out old and broken hold down clips, installed new ones(4). Cut old wires attached to surface plug in block, striped wires, and attached new plugin kit(4), warmed up heat shrink with a hair dryer, put in new drip bowels, the stove is like new.I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon Read more...
Your Price
$34.09
In Stock
Cooktop Terminal Block
PartSelect Number PS11750972
Manufacturer Part Number WPW10245259
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Touchpad does not respond
- See more...
Installation Instructions
Joseph from Decatur, GA
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Read more...
Your Price
$38.11
In Stock
Cooktop Receptacle Kit
Piece of cake, but then again my degree is in electrical engineering so I should be able to handle a couple of wire nuts. Read more...
PartSelect Number PS389217
Manufacturer Part Number 814399
This assembly of parts is a surface burner receptacle kit, and is used in conjunction with your range. The assembly comes with two wires, two wire nuts, two pieces of heat-shrink tubing, and the receptacle. If your element is not heating, you may need to replace your surface burner receptacle. The function of this part is to connect the surface element to the wire harness. The tools you will need for this installment include a number two square-head screwdriver or a number two Phillips screwdriver, a pair of wire strippers and crimpers, and a heat gun.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Tim from Pittsford, NY
Stove would not heat up
Cut old wires to receptacle, striped the wires, wire nutted to new receptacle, screwed new receptacle into stove and installed heating element.Piece of cake, but then again my degree is in electrical engineering so I should be able to handle a couple of wire nuts. Read more...
Your Price
$31.61
In Stock
Cooktop Surface Burner Terminal Block Kit
PartSelect Number PS242972
Manufacturer Part Number WB2X8228
Also known as receptacle.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Robert from Mt. Vernon, IN
The Bake-o-lite (Hard Plastic) block that holds the burners female connection in place had chipped away over time and wouldn't allow the male part of the burner to connect up correctly.
After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From rear I carfully pulled the old wires through the back until I could reach the new wiring connections. Unplugged old, plugged in new and replaced the rear metal cover. Then I put the screw that holds the new block bracket in place, replaced drip pan, and burner. The final step was to plug the range back in and check to see if the burner worked. It did and I was done. Approx. 5 minutes
Read more...
Your Price
$78.35
In Stock
Cooktop Surface Burner Terminal Block Kit
PartSelect Number PS232606
Manufacturer Part Number WB17X210
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance before starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Shaohui from East Lansing, MI
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Read more...
Your Price
$56.72
In Stock
Cooktop Terminal Block Kit
PartSelect Number PS953027
Manufacturer Part Number WB17T10011
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
jonathan from willow springs, IL
terminal block melted
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
Read more...
Your Price
$38.38
In Stock
Cooktop Terminal Block
PartSelect Number PS232646
Manufacturer Part Number WB17X5113
This kit includes one ceramic block with 6" wire leads, 2 wire nuts and 2 heat shrink with mounting bracket.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Richard from Apex, NC
Heating element required continuous adjustments to work.
I removed old 8" surface element and terminal block. Some of old wiring had to be cut off because of harding/cracking of old wiring. Stove was 23 years old and this burner was the most frequently used one. I soldered the new and remaining old wires together. I used the shirnk wrap that came with the terminal block to cover the solder joint. I screwed the new terminal block (one screw holds it in place - used same screw from old terminal block that was removed). I finished by inserting the new surface element. Everything works fine. In the next week or two after we use it a while, I will check wiring again to make sure there are no changes. You need to be very careful as it gets very hot under the burner.
Read more...
