PartSelect Appliance Parts Blog

Paint Your Appliance Pink

PartSelect — Tue, 30 Jun 2009 15:29:38 GMT

PartSelect.com is thrilled to announce Paint Your Appliance Pink!

The sweeps runs from July 1, 2009 – September 1, 2009 and contestants can enter to win 1 of 3 Pink Prize Packages valued at $369.97. Plus, PartSelect will donate $25 to the the Breast Cancer Research Foundation for every photo entry received (up to a max of $10,000).

It's so easy to enter!

Paint a pink ribbon on any major home appliance
Take a photo of your appliance
Tell us about your entry:

Email us: contests@partselect.com with the attached photo.
Tweet us: @PartSelect, tag your tweet with #pinkappliance and include a link to your picture (blog post, twitpic, etc.).
Facebook: Join our Facebook group and post your entry there.

Each contestant will be entered into a monthly draw to win 1 of 3 Pink Prize Packages.

The Pink Prize Packages consist of a Pink KitchenAid Stand Mixer, Pink Stand Mixer Cover, Pink Silicone Spatula, Pink Silicone Heart Pan, Pink Measuring Cups and Spoons Set, and a Cook For The Cure Apron. Draws will take place on August 3, 2009, September 3, 2009, and October 3, 2009.

For full details and rules check out the official sweeps web page.

How To Replace a Washer Coupler ( Whirlpool or Maytag)

PartSelect — Thu, 23 Oct 2008 18:12:32 GMT

Tools:

Putty knife
1/4 inch nut driver or socket
Phillips screwdriver
Flat tip screwdriver
Hammer and piece of pipe
Container for screws

Before attempting any appliance repair, be certain you have unplugged the appliance and completely disconnected it from any power source.

To begin you must remove the control panel. For some Whirlpool models, you will need to remove two screws from the back of the unit. If there are no screws on the upper back part of the unit, then you will have to remove the end caps to the control panel to expose the screws. For Maytag models, slide a putty knife under the control panel on the extreme left (so you do not damage the lid switch) and pop it up. Repeat this on the far right. Using a flat tip screwdriver, pop out the brass springs holding the control panel to the cabinet and the control panel should be released from the unit

and you can flip it up away from you. and the control panel should be released from the unit and you can flip it up away from you. Disconnect the lid switch and make sure not to let it fall in between the dryer and the control panel.

With the lid open and your hands on the inside, grasp the cabinet and tilt it forward and lift upward at the same time to release it. Place it out of the way. The pump and motor will be located at the bottom on the front.

You will need to start by releasing the two clips holding the pump to the motor and swinging it out of the way. You don’t need to remove any of the hoses to do this. Next, disconnect the wiring harness located on the right side of the motor and remove the two brackets and screws holding the motor in place. Now, you should be able to pull out the motor and see the coupler. Part of the coupler will be on the motor

and part of it will be still on the transmission that is now exposed. Remove the old coupler and start by replacing the half on the transmission shaft. You may need a hammer and a piece of pipe to secure this piece. Replace the rest of the coupler on the motor and put the motor back on. Replace the motor brackets and screws and reconnect the wiring harness. Next, replace the pump and pump brackets.

Now you are ready to place the cabinet back on. Make sure the small holes on the cabinet bottom line up with the tabs. Finally, flip the control panel back over and replace spring clips and screws if necessary.

How To Replace a Dryer Belt on Whirlpool Models

PartSelect — Thu, 23 Oct 2008 18:09:25 GMT

Tools:

5/16th nut driver or socket
Phillips screwdriver
Putty knife
Container for screws

Before beginning any appliance repair, it is extremely important to make sure the appliance you are repairing is unplugged and is completely disconnected from power.

The first step in replacing a dryer belt is to slide out the lint filter. This will reveal two screws, which need to be removed in order to get the top of the dryer off. Next, take a putty knife and slide it in to the small opening between the top of the dryer and the front of the dryer. Using the knife, you can pop the top of the dryer off. Do this on the left and the right and flip the top of the dryer out of the way. It’s a good idea to prop the top against something so it doesn’t strain the brackets.

Now that the inside of the dryer is exposed, you have access to the two screws holding the front in place. Using the 5/16th driver, remove the screws on the upper inside right and left corners. This will release the front of the dryer and you can pull out and up to detach it from the rest of the dryer and swing it to the side, out of the way. You may have to disconnect the lid switch if the wires aren’t long enough to allow this.

With the dryer fully exposed now, you can pull off the old belt. Since the inside of a dryer can accumulate a lot of dirt, it’s a good idea to vacuum it out while you have it apart. Simply pull out the drum, vacuum, and replace.

To put on the new belt, you may need another person to help you hold up the drum. It sags down over the area you need to work with and an extra hand can make the next part easier. Start by placing the belt over the entire drum. Next, you will have to go underneath the drum where the idler pulley and motor is located. The belt needs to be placed through the idler pulley and then attached to the motor. The picture shown is with the drum removed so it’s easier to see how the belt is attached. If this is done

properly, the idler pulley should apply tension to the belt.

After the belt has been secured, you should check the rear felt that is on the back end of the drum to make sure it has not been folded under. If it has, use a screwdriver to pop it out while spinning the dryer drum. Finish by replacing the front of the dryer, making sure the tabs on the bottom of the dryer are lined up with the small holes on the front. Connect the lid switch if necessary and replace screws from the inside top corners and lint trap. Finally, replace your lint trap and you’re finished.

Save On Energy-Guzzling, Electricity-Sucking Appliances

PartSelect — Fri, 19 Sep 2008 13:05:42 GMT

We all want to make a difference by helping our environment and we’d love to save some money on our power bills, but let’s face it - when it comes to energy-guzzling major home appliances, getting rid of them is not an option. So when you’re stuck with a necessity that could be doing damage to the environment and your wallet, what’s a homeowner to do? It comes down to compromise and taking action to minimize the damage. And the best place to start is with some of the greediest appliances in the home.

    The first offender is one of the most used appliances in any home, the refrigerator. Many people don’t have a clue that their refrigerator accounts for 5% of their yearly energy bill, a figure that doubles if your fridge is made before 1993. Combine this with bad habits, such as leaving the door open while you select your midnight snack, and you’ve got a sure fire way to waste energy and money. Since you can’t simply shut off your refrigerator, make it more energy efficient by doing things like cleaning the coils on the backside and underneath. A fridge will cycle less when the coils are free of dirt and debris and a steady temperature of 35-38 degrees Fahrenheit helps make a difference too. It’s also a good idea to make sure your fridge is kept away from heat sources, such as ovens and heaters, and to leave a space between the wall and fridge for air to circulate. Of course, don’t forget to minimize the time you leave the door open when deciding what to munch on.

    The next greedy guzzler on the list is the clothes dryer, which is typically the second biggest electricity sucker in the home. In fact, clothes dryers are so inefficient they haven’t even earned an EnergyStar label. There isn’t much you can do to make your clothes dryer more earth-friendly (aside from splurging for a new, more efficient model) but you can avoid over-drying by using your dryer’s moisture sensor settings so it shuts off when your clothes are dry. You should also only run it with full loads, keep the lint trap clean, and if you really want to make a difference on your bill, grab some rope and clothespins and make a good old fashioned clothes line.

    The dishwasher may feel like a necessity to many but for the most part, owning one is really a luxury and an energy sucker. But don’t feel bad just yet, you can have your cake and eat it too if you use your dishwasher wisely. First, only run the dishwasher if there is a full load of dishes and let them air dry rather than wasting all that energy the dishwasher uses. Another no-brainer is to try to use fewer dishes in the course of a day. Fewer dishes mean fewer loads and that means fewer dollars of your money going down the drain. And lastly, make sure you only pre-rinse your dishes when necessary (burnt on food) and if you’ve pre-rinsed them by hand, don’t run the pre-rinse cycle when you do your load of dishes. Need more green ideas for your dishwasher? Treehugger.com is always a great resource.

    The clothes washer is not an appliance anyone wants to live without but don’t let that stop you from using it more efficiently. The truth of it is, there is one very simple thing you can do to save 90% of the energy a clothes washer consumes – wash in cold water. This is the biggest reason why washers are considered energy guzzlers and even using the warm water option will cut the energy used by half. Since a washer uses pretty much the same amount of energy regardless of load size, running full loads as much as possible is another energy saving tip. In fact, there are several seemingly small things you can do to save energy with your washing machine.

    Granted the best way to make an impact on the amount of energy your appliances use is to invest in some EnergyStar appliances. They do cost a little more but in the long run, they’ll save you money on your energy bills and really help the environment. But if you don’t have the extra green in your wallet to buy new appliances, don’t despair. There are several easy things you can do today to make your home more green. Eliminate some bad habits, make a few small sacrifices and most importantly be conscious of what you’re appliances are doing, or rather consuming.

For more energy saving tips:
13 Simple Ways to Lower Your Electric Bill
Save Energy Through Your Appliances

9 Wacky Ways To Reuse Appliance Parts

PartSelect — Thu, 18 Sep 2008 17:17:24 GMT

Want to do something creative and environmentally friendly with your old appliances? Is the old fashioned way of disposal just too boring for your tastes? Then try out these zany and even practical ways to reuse your household appliances.

1. Turn your old washer drum into a rustic, outdoor fire pit! The holes in the drum allow air to get in and let your fire “breathe”.

2. Use your old dryer as a storage bin for apples and potatoes. You can even reuse that endless dryer lint!

3. How about converting your old fridge into a tool shed or storage closet for the basement or garage?

4. If you’re good with your hands, you can get really creative and make a lamp out a washing machine drum and pulley wheels.

5. Check out this video called Trash To Treasures Gardening and find out how you can use broken pots, old stove parts and more to decorate your garden in a truly unique way.

6. If your home landscape lacks some greenery, reuse a washer tub, dryer tub, or even an old BBQ as a plant pot.

7. Get really innovative like this guy and build your very own scooter using some old appliance parts.

8. Got a mind for engineering or robotics? Let your old appliances inspire you to build a robot.

9. You can even be inventive with appliance parts, such as circuit boards, with these Ten Creative Ways To Reuse Circuit Boards.

By being inventive, imaginative and conscious of your waste, you can actually do something creative that helps the environment. Who knew being green could be so much fun?

Recycling Your Old Appliances

PartSelect — Wed, 17 Sep 2008 20:08:52 GMT

There are thousands of ways we can be ‘green’ and help do our part to protect our environment. From recycling old newspapers and pop bottles to donating used clothing and furniture, it seems there is a way to recycle or reuse just about everything. So why is it many homeowners forget about recycling their old household appliances? When it comes time to dump that outdated or worn-out appliance, resist the urge to toss it in the dump and do your part to properly dispose or recycle it. As you’ll see, it can be as easy a phone call!

Bounty and Municipal Programs
    If you need to get rid of an old appliance the first thing you should do is call your electric utility and see if they offer a bounty program in your area. These programs can give you a rebate for your old, unwanted appliances. Generally, these appliances do have to meet certain requirements and be in working condition to qualify.
You can also try to arrange an appointment with your municipality to have your appliance picked up or to find out where you can take them to be disposed. Find out more about these programs by calling your municipality or checking out the Environmental Protection Agency’s FAQ on disposing appliances.

Donation Programs
    Why recycle an appliance when another family can reuse it? If you’re updating your home and have decided to get new appliances, you can donate your old appliances through various donation programs such as the Salvation Army. These organizations are a great way to get rid of any home appliance but they do need to be in working condition before they are accepted. If you’re interested in these types of programs, there are several options available here and here.

Disposing of Appliance with Refrigerants
    Appliances containing refrigerants need special attention when being disposed. Refrigerators, air conditioners, and dehumidifiers all contain dangerous refrigerants such as Freon, which can deplete the ozone if not properly disposed. If you need to get rid of one of these appliances and they do not qualify for one of the above programs, check out the US Environmental Protection Agency for proper disposal. Remember, never under any circumstance attempt to remove refrigerants yourself as they can cause you and the planet physical harm.

    We all share the responsibility of keeping our communities and the environment safe and with so many options available, there’s no reason not to. So next time you’re thinking of throwing out an appliance, or anything else for that matter, make sure you stop and think about the safest and friendliest way to do so. If we all work together, we can make a difference.

For more information on recycling and proper household hazardous waste disposal:
Appliance Recycling Centers of America
Association of Home Appliance Manufacturers
American Council for an Energy-Efficient Economy
Earth911
Natural Resources Canada

Whirlpool Fault Codes

PartSelect — Wed, 17 Sep 2008 20:00:14 GMT

Attention: We do not offer any further information on appliance fault codes. If you require extra assistance, please contact an appliance repair technician.

Whirpool Oven/Range/Stove Fault Codes (Including 2 and 4 digit codes)
Note: Depending upon the brand of appliance, there can be many different names for the 'clock' component. Electronic Range Control, ERC, Electronic Oven Control, EOC, control board, and clock all refer to the same part.

4 Digit Fault Codes
F1-E0 - EEPROM Communication Error - Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
F1-E2 - UL A/D Error(s) - Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
F1-E4 - Model ID Error - Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
F1-E5 - Calibration Shifted - Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
F1-E6 - Latch Signal Mismatch Error - Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
F1-E3 - Wiring Harness Cavity Size Does Not Match Stored Value - Check the jumpers in the harness to make sure they agree with the actual oven size.
F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
F2-E1 - Touch Pad (Keypad) Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
F2-E6 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD).
F4-E1 - Meat Probe Defect - This error indicates a problem with either the probe, receptacle, or probe circuit. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. If ok, replace probe.
All F5-E Codes - Door Switch Defect - This occurs when the door switches do not match. If door is latched, disconnect power from unit and check wires and connections. If damage is found, replace appropriate part. If connections are not damaged, reconnect power and hold down any key until the F5 error clears. Once the F2 code appears, select 'cancel' and observe for one minute for errors. If door is NOT latched, disconnect power from unit and check wires and connections. If damage is found, replace appropriate part. If connections are not damaged, measure door switch (door open = latch open) and latch switch (unlatch = switch open) and replace either if defective. If corrections are made during any step, power should be reconnected and the unit should be tested. Press and hold any key to clear the error code and F2 code should appear. Select 'cancel' and observe for one minute for errors. If error continues, disconnect power and replace control.
F6-E0 - Return Line Not Connected - This error should appear within 60 seconds after power up to appliance. Replace control board (clock).
F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. Check all connections at control board and at the latch switch and door switch. If connections are ok, then check individual switches as outlined for the F5 error code. Note: Double ovens will have two of each switch and one common wire.

2 Digit Failure Codes
F0 - Control Board Failure - Replace control board (clock).
F1 - Control Board Failure - Replace control board (clock).
F2 - Oven Temperature Is Too High - Check for welded contacts on bake and broil relays. If present, replace control board (clock). For SELF CLEAN models, check door lock operation. Check sensor, sensor harness, and the sensor harness connection at sensor and oven control. Also check for any causes of high resistance in the oven temperature sensor circuit. Remember: The oven control board (clock) measures resistance of sensor circuit, not actual oven temperature.
F3 - Open Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD).
F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD).
F5 - Control Board Failure - Replace control board (clock).
F7 - Function Key Stuck - Replace control board (clock).
F8 - Control Board Failure - Replace control board (clock).
F9 - Oven Door Lock Failure - Check door lock switches and wiring. Check for stuck lock switch.

Whirpool Duet Front Loading Automatic Washer Fault Codes

FH - Detects No Water Entering Machine or No Pressure Switch Trip - Select 'cancel' twice to clear this code. If there is NO water in the unit, make sure the valves are turned on all the way. Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. Verify that the inlet valve is operational. If there is water in the unit, verify the drain pump is working and the pressure switch hose is in good condition and properly connected. Make sure there is not a siphon problem and check all hoses for possible leaks. Unplug the unit and disconnect the power to check all wire harness connections to the inlet valve, pressure switch, drain pump, flow meter, and Central Control Unit (CCU). Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance). Check CCU is also operational by performing a diagnostic test or any cycle. Replace failed component.
F02 - Long Drain (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. Note: You may see a "SUD" error code appear first during this failure. This should change to the F02 error code after a few minutes. Proceed by checking the drain hoses for proper connection and kinks. Unplug unit and disconnect power. Check the electrical connections at the pump and make sure it is operational with no debris or blockage. Reconnect power and plug unit in. If problem has not been corrected, replace the pump.
F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check all connections to the water temperature sensor, heating element and element relay. Also check all components for defects. Replace failed component.
F06 - Drive Motor Tachometer Error (Unable to Detect Motor Speed) - Disconnect power and unplug unit. Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Reconnect power and plug unit in. Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Replace failed component. Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.
F07 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit. Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Reconnect power and plug unit in. Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Replace failed component. Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.
F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Check for drain pump failure and clean it of any debris. Check the inlet valve and pressure switch for proper shut off and operation. Replace failed component. Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. Turn off hot and cold water to faucets and unplug the unit before proceeding.
F10 - Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot) - Check for proper installation and ventilation, and make sure unit is not located near a heat source. Disconnect power and unplug the unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). Check the drive system for any worn or failed components and reconnect power and plug unit in. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. Replace failed component.
F11 - Serial Communication Error Between MCU and CCU - Disconnect power and unplug unit. Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU). Check the drive system for any worm or failed components and reconnect power and plug unit in. Verify CCU is working by performing diagnostic test or any cycle. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. Also check the motor and wire harness. Replace defective part.
F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. Check wire harness connections to the Central Control Unit (CCU) and the dispenser motor. Check dispenser motor for powered rotations. Replace failed component.
F14 - EEPROM Error - Disconnect power and unplug unit. Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle. Replace is defective. Note: A power glitch may cause this error. Try unplugging unit for two minutes to see if that fixes error.
F15 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). Check the drive belt and reconnect power and plug unit in. Check the MCU by looking for operations of the drive motor and check the drive motor for powered rotations. Replace failed component.
FdU - Door Unlock Error - It is possible the door lock mechanism is broken or the door switch/lock unit has failed. Check the door switch/lock for any debris or foreign objects. Disconnect power and unplug unit to check wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Note: Unit will attempt to unlock itself during this error six times before displaying this error code. To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel. Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Gently pull the tab down approximately 1/4 inch or until a 'click' is heard. The door should now be unlocked.
FdL - Door Lock Error - It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed. Disconnect power and unplug unit to check door switch/lock unit. Check the wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Note: Unit will attempt to lock itself during this error six times before displaying the error code.
SUD - Suds Lock (Too Much Detergent Detected) - Make sure drain hose is not plugged or kinked and disconnect power and unplug unit. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in. Check drain pump and pressure switch and verify CCU operation by running a diagnostic test or any cycle. Note: This error may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. If too much detergent was used, run the unit through a Rinse/Spin cycle, and then run a Normal cycle without adding detergent.

Whirpool Duet Front Loading Gas and Electric Dryer Fault Codes

PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. Press and HOLD start to continue the cycle, or press off/pause to clear display.
E1 - Open Thermistor - Replace thermistor.
E2 - Shorted Thermistor - Replace thermistor.

Whirpool Calypso Automatic Washer Fault Codes

PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. Press and HOLD start to continue the cycle, or press 'Stop/Cancel' to clear display and cancel cycle.
FL - Flood Condition - FL error code will appear when the unit detects an overfill, or excessive amounts of water in tub. When this error occurs, the pump should be cycled in drain mode for 30 seconds on and 30 seconds off until the switch resets. Press 'Stop/Cancel' to clear display.
Er - Processor Reset Error - This error will only occur if the unit fails to save cycle information during a power outage. Press 'Stop/Cancel' to clear display.
LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display. Press 'Stop/Cancel' to clear display.
CE - Communication Error - Disconnect power and unplug unit. Check for conformal coating on serial communication pins between the machine controller and the motor controller. Make sure the harness does not have a faulty connection by checking the resistance values between serial communication pins with the connectors in place.
Ld - Long Drain - This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. Press 'Stop/Cancel' to clear display.
CA / CI - Average Current Limit / Instantaneous Current Limit - This error code may signify a problem with the drive motor, thermal protector, or motor controller. Overloading the unit may also cause this problem.
ob - Off Balance - The lid switch must be opened at least once before reseting the cycle. Opening the lid will allow you to redistribute the load to avoid a further off balance error. Press 'Stop/Cancel' to clear display.
Sr - Stuck Relay - The machine control board may have a bad relay and may need to be replaced. Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. This should have AC line voltage when the motor controller is powered. Press 'Stop/Cancel' to clear display.
LS - Lid Switch Error - This error will occur if unit cannot detect the lid switch opening or closing. It is also possible this error code will appear is there is a disagreement between the motor and machine controllers. Open the lid or press 'Stop/Cancel' to clear display.
Flashing Display Time - Open Lid - This will only occur if the lid is opened during a running cycle. Close the lid and press 'Start' to continue.
SL - Suds Lock - This error will occur if the unit detects suds but is unable to clean them out. The unit will attempt the clean out the suds three times before displaying this error. It can also indicate a bad pump, an extra heavy load, excessive detergent, or excessive suds. Press 'Stop/Cancel' to clear the display.

Westinghouse Fault Codes

PartSelect — Wed, 17 Sep 2008 19:54:34 GMT

Attention: We do not offer any further information on appliance fault codes. If you require extra assistance, please contact an appliance repair technician.

Westinghouse Oven/Range/Stove Fault Codes
Note: Depending upon the brand of appliance, there can be many different names for the 'clock' component. Electronic Range Control, ERC, Electronic Oven Control, EOC, control board, and clock all refer to the same part.

F0 / F1 - Control Board Failure - Replace control board (clock).
F2 - Oven Temperature Too Hot - Check oven temperature sensor. Replace if defective. If oven temperature sensor is ok, replace control board (clock).
F3 / F4 - Open or Shorted Oven Temperature Sensor - Replace oven temperature sensor.
F5 / F6 / F7 - Control Board Failure - Replace control board (clock).

Thermador Fault Codes

PartSelect — Wed, 17 Sep 2008 19:53:48 GMT

Attention: We do not offer any further information on appliance fault codes. If you require extra assistance, please contact an appliance repair technician.

Thermador Oven/Range/Stove Fault Codes (Starting with F)
Note: Depending upon the brand of appliance, there can be many different names for the 'clock' component. Electronic Range Control, ERC, Electronic Oven Control, EOC, control board, and clock all refer to the same part.

F0 - Oven Control Failure - Replace control board (clock).
F1 - Oven Control Failure - Replace control board (clock).
F2 - Oven Temperature Too Hot - Replace relay board if faulty. Check and replace oven temperature sensor (RTD). If error persists, replace control board (clock).
F3 - Open Oven Temperature Sensor (RTD) - Check the connection between the oven control and oven sensor, as well as the sensor harness. If wiring is ok, replace oven temperature sensor (RTD).
F4 - Shorted Oven Temperature Sensor (RTD) - Check the connection between the oven control and oven sensor, as well as the sensor harness. If wiring is ok, replace oven temperature sensor (RTD).
F7 - Function Key Stuck - Check all keys on touch pad (keypad). Replace control board (clock).
F8 - Internal Logic Failure - Check the connection between the oven control and oven sensor, as well as the sensor harness. If wiring is ok, replace oven temperature sensor (RTD) and control board (clock).
F9 - Internal Logic Failure - Check door latch and switches and replace if defective. Replace control board (clock) if everything else is ok.
Fd - Bake And Broil Relay Drives Act Simultaneously - Check relay board and control board (clock). Replace if damaged.

Thermador Oven/Range/Stove Fault Codes (Starting with E)
Note: Depending upon the brand of appliance, there can be many different names for the 'clock' component. Electronic Range Control, ERC, Electronic Oven Control, EOC, control board, and clock all refer to the same part.

E1 - Control Board Failure - Replace control board (clock).
E2 - Oven Temperature Sensor (RTD) Fault - Check oven temperature sensor and replace if faulty. If sensor is ok, replace control board (clock).
E3- Open Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD).
E4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD).
E5 - Control Board Failure - Replace control board (clock).
E6 - Control Board Failure - Replace control board (clock).
E7 - Control Board Failure - Replace control board (clock).
E8 - Control Board Failure - Replace control board (clock).
E9 - Door Latch Switch Problem - Check door latch switches and wiring. Replace if faulty.
E10 - Control Board Failure - Replace control board (clock).
E11 - Door Latch Switch Problem - Check door latch switches and wiring. Replace if faulty.
E12 - Door Latch Switch Problem - Check door latch switches and wiring. Replace if faulty.
E13 - Latch Motor/Control Board Failure - For CT models, check power to latch motor. For CMT models, the control board has not converted.
E14 - Door Latch Switch Problem - Check door latch switches and wiring. Replace if faulty.
E15 - Control Board Failure - Replace control board (clock).

Tappan Fault Codes

PartSelect — Wed, 17 Sep 2008 19:52:12 GMT

Attention: We do not offer any further information on appliance fault codes. If you require extra assistance, please contact an appliance repair technician.

Tappan Oven/Range/Stove Fault Codes
Note: Depending upon the brand of appliance, there can be many different names for the 'clock' component. Electronic Range Control, ERC, Electronic Oven Control, EOC, control board, and clock all refer to the same part.

F0 - Oven Control Failure - Replace control board (clock).
F1 - Oven Control Failure - Replace control board (clock)
F2 - Oven Temperature Too Hot - Check and replace oven temperature sensor (RTD).
F3 - Open Oven Temperature Sensor (RTD) - Check the connection between the oven control and oven sensor, as well as the sensor harness. If wiring is ok, replace oven temperature sensor (RTD).
F4 - Shorted Oven Temperature Sensor (RTD) - Check the connection between the oven control and oven sensor, as well as the sensor harness. If wiring is ok, replace oven temperature sensor (RTD).
F5 - Oven Control Failure - Replace control board (clock).
F6 - Oven Control Failure - Replace control board (clock).
F8 - Oven Door Lock Failure - Check door lock switches and relay.