Quick Question!

Have you ever purchased from PartSelect.com before?

Popular Amana Range Parts

Your Price
$3.88
Light Bulb - 40W
PartSelect Number PS884734
Manufacturer Part Number 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-out bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
judie from mays landing, NJ says,

interior drawers were off their rollers
pulled the washer out and replaces the top roller system on both sides and the replaced the weels and brackets on the bottom drwaer. however i had trouble putting the dish washer back correctly and ha...read more

Your Price
$4.17
Chrome Drip Bowl - 8"
PartSelect Number PS11750107
Manufacturer Part Number WPW10196405
This drip bowl is also known as a drip pan, and it is designed for use with cooktops and ranges. It sits below 8-inch burner elements, and catches drips and spills from the cookware on the burner. The diameter of the drip bowl is approximately 9 3/4 inches. This replacement might appear slightly different, but it will fit your appliance. You will need no tools to complete this repair. Simply remove the burner element, remove the old bowl, line the hole on the new bowl up with the terminal block and drop it into place. Make sure the bowl is flat before reinstalling the element. While you have the element out you should inspect the terminals for corrosion, damage, or discoloration. If you notice any of those things you should also replace the element and terminal block. You will need to replace your drip bowl if it is lost, damaged, or can no longer be cleaned. This replacement part is sold individually. To extend the life of your new drip bowl we recommend you clean it regularly with soap and water.
Fixes these symptoms
Element will not heat


Installation Instructions
Joe from Greeley, CO says,

oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then removed element and replaced with new
....read more

Your Price
$24.04
2 Piece Broiler Pan
PartSelect Number PS971245
Manufacturer Part Number 4396923
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set includes both the pan and the grid. The grid is the top part. The slotted design allows grease to easily drip into to the pan below. Not only does it catch all of the drippings, it also prevents splatter and smoke while cooking. The pan can also be used separately for baking and roasting. This cookware features a durable porcelain finish, which means it is incredibly easy to clean, and is dishwasher safe. It is roughly 1.5 inches deep, and measures approximately 16.5 inches by 12.5 inches. If your two-piece broil plan is lost, rusted, or damaged this is the replacement you need.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Lois from Elmer, NJ says,

Bought house & stove was missing rack & broiler
slid in groove

shipment & arrival of new parts unbelievably fast....thanks...read more

Your Price
$4.04
Drip Bowl - 6"
PartSelect Number PS11750108
Manufacturer Part Number WPW10196406
This drip bowl is used for electric cooktops and ranges, it is designed to sit under a six-inch surface burner. It catches the drips and spills coming from the cookware on the surface burner. This drip bowl is chrome, and it has a diameter of 7 2/3 inches. You need to remove the burner element to replace this part. Line the hole up with the element terminal blocks, and ensure the new bowl is flush with the surface of the cooktop before replacing the burner element. Drip bowls need to be replaced when they are lost, damaged, or you are no longer able to clean them adequately. This replacement part is sold individually.
Fixes these symptoms
Element will not heat


Installation Instructions
Joe from Greeley, CO says,

oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then removed element and replaced with new
....read more

Your Price
$11.12
Surface Burner Plug-In Block Kit
PartSelect Number PS340571
Manufacturer Part Number 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Fixes these symptoms
Element will not heat


Installation Instructions
Jon from Oakley, CA says,

Surface elements quit working
Drilled out old and broken hold down clips, installed new ones(4). Cut old wires attached to surface plug in block, striped wires, and attached new plugin kit(4), warmed up heat shrink with a hair dry...read more

Your Price
$19.90
Terminal Block
PartSelect Number PS11750972
Manufacturer Part Number WPW10245259
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.
Fixes these symptoms
Element will not heat
Little to no heat when baking
Will Not Start

See more...
Installation Instructions
Joseph from Decatur, GA says,

Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem....read more

Your Price
$29.74
Long Oven Sensor
PartSelect Number PS1570174
Manufacturer Part Number 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.
Fixes these symptoms
Door won’t open after self cleaning cycle
Element will not heat
Little to no heat when baking

See more...
Installation Instructions
David from Westford, MA says,

Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic con...read more

Your Price
$46.04
Flat Style Oven Igniter
PartSelect Number PS387058
Manufacturer Part Number 786324
The flat style oven igniter is also known as a range oven igniter. The function of this part is to glow extremely hot in order to ignite the gas for the oven burner. With this flat style oven igniter, you must reuse the original bracket from your original igniter. Be very careful during installation to not touch the black element part of the flat style oven igniter as it is very fragile. If your oven does not heat you should check to see if your igniter is glowing. If your igniter is glowing and the oven is not heating there is a chance that the igniter is not strong enough to heat your oven and it will need to be replaced.
Fixes these symptoms
Element will not heat
Gas igniter glows, but will not light
Little to no heat when baking

See more...
Installation Instructions
John from Niles, MI says,

Oven wouldn't heat. Glow ignitor was weak and wouldn't ignite flame.
After shutting off the gas and removing the oven door, which simply slid off of the hinges, I removed the oven plate. The ignitor was attached to the manifold. I removed that and noted the wires wer...read more

Your Price
$9.11
8" Drip Bowl - Black
PartSelect Number PS11752111
Manufacturer Part Number WPW10290350
This black porcelain drip bowl with a hole in the bottom is intended for use with some electric ranges and cooktops. This drip bowl measures 10 inches in diameter at its widest point. The purpose of the drip bowl is to catch any spills or grease from the cookware sitting on the burner. The drip bowl might burn, rust, or get to the point where you can no longer get it clean, and will need to be replaced. You will need to remove the surface burner to remove the old drip bowl. These bowls are dishwasher-safe.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Elizabeth from Fruitland Park, FL says,

Needed new drip bowls for my stove top burners
After trying for many years to buy the "cheap" drip pans in the store, "They never fit right", I decided to order the correct drip bowls. Now my stove top looks brand new, and my coil elements fit the...read more

Your Price
$50.37
Oven Igniter - Vertical Mount
PartSelect Number PS2085070
Manufacturer Part Number 74007498
This broil igniter assembly comes with its own metallic mounting bracket and a 7-inch-long dual wire lead with a plastic plug. This part will need to be repaired if your oven element is giving off no heat or very little, or is not heating evenly. You may also notice a smell of gas. The ignitor may still be glowing, but could still have gone bad. You will need a 1/4-inch nut-driver and a 5/16 nut-driver. Open the oven door and pull the door off the hinges to completely remove. Pull out the racks. Using your 1/4-inch nut driver, take out the screws at the bottom rear end of the oven, which will allow you to completely remove the bottom. Unscrew the nuts holding the igniter in place. Remove the igniter with the 5/16 nut driver. You should now have access to remove the old igniter.
Fixes these symptoms
Element will not heat
Gas igniter glows, but will not light
Gas smell

See more...
Installation Instructions
James from Berwick, ME says,

Oven wouldn’t heat up properly
My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, ...read more