Parts That Fix Whirlpool Washer LSQ8543JQ0 Will not agitate
Will not agitate is a commonly reported symptom for the LSQ8543JQ0 Whirlpool Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your LSQ8543JQ0 Whirlpool Washer that will fix Will not agitate. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what prevent the agitator from rotating in both directions, while allowing it to rotate in one direction. Your agitator cogs may be malfunctioning if you can manually rotate the agitator in both directions. If broken they will need to be replaced. Cogs can be found by simply removing the softener dispenser and then removing the agitator cap. The are attached to the agitator. This replacement part features 4 agitator directional cogs. There are 4 cogs per package that are made up of high-quality plastic. This part comes in white/beige.
Replacing your Whirlpool Washer Agitator Directional Cogs
Customer Repair Stories
top half of agitator did not move during wash cycle
-
dennis from new stanton, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
washer wouldn't agitate
Slip the new cogs into the underside of the cup, and slide the cup back down in the a ... Read more gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
-
mike from Kent, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Replacing your Whirlpool Washer Direct Drive Motor Coupling
Customer Repair Stories
Broken Coupling
1. Removed hoses from the pump
2. Removed Wiring harness from the motor
3. Unscrewed saftey screws from both clamps which hold the motor against the motor bracket.
4. Using a screw driver I easily removed/pryed the clamps from the motor.
5. I then removed the broken plastic coupler from the motor sha ... Read more ft and installed the new one coupler.
6. I did the same thing on the clutch side.
7. I set the Rubber coupler in clutch side.
8. Put motor back on until couplers joined together.
9. Placed Brackets back on Motor (patience here).
10. screwed back saftey screws on clamps.
11. connected hoses back.
Thats it... 45 minutes at most .. Save me from having to buy a new easher. I was convinced I was going to have too until I peeked underneatch the washer and saw the rubber coupler on the ground...
-
Hugo from Frisco, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
No movement from Basket & agitator
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum ... Read more p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
-
Jeff from Wayne, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
This kit included the cam, 4 dogs and bearing.
Replacing your Whirlpool Washer Agitator Cam Kit
Customer Repair Stories
Agitator was skipping, making grinding noise
-
Jeffrey from Williamstown, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Dog ears worn down; upper agitator not moving
-
shawn from la jolla, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Replacing your Kenmore Washer Agitator Bolt
Customer Repair Stories
The agitator had stopped working
-
Jack from Matthews, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
could not get the bottom agitator to release, so finally just left it in place, first bolt I had did not fit right so ordered one directly from your store also had to wait dor my tools to get in
-
Linda Dianne from Poteau, OK
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Socket set
This agitator comes with the 4 agitator dogs (cogs) and top mover. The cap is NOT included with the agitator.
Replacing your Whirlpool Washer Washer Agitator
Customer Repair Stories
Agitator was not working properly due to broken plastic pieces in agitator
-
doug from spokane, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
Top section of agirtator not working
-
Vincent from York, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inches in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.
Replacing your Whirlpool Washer Seal, Inner Cap
Customer Repair Stories
The cap thingy seal broke and splattered fabric softener.
-
Diane from Corvallis, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
The seal in the upper agitator cap broke
-
Veronica L from Junction City, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.
Replacing your Whirlpool Washer Agitator Cap Barrier with Seal
Customer Repair Stories
The seal was broken on the agitator cap barrier
-
Ralph from New Milford, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Found seal had split on agitator cap
Thanks for making finding part ... Read more so easy . . . .
-
Kim from Cleveland, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Sits in between the agitator base and upper agitator.
Customer Repair Stories
My washer was squealing on the spin cycle! Also shaking & moving!
-
Donna from IRON MOUNTAIN, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set, Wrench (Adjustable)
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining is worn out, the clutch assembly will not rotate properly to release the brake. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate there is an issue with your clutch. If the washer spins when the washer basket is empty but not when it’s full, or if the assembly begins to turn blue, you may need to replace the clutch assembly. This assembly includes a brake cam driver, blue springs for large capacity washers, a black spring for compact washers, and the installation instructions. It’s constructed of plastic and metal, and comes in beige/silver.
Replacing your Whirlpool Washer Clutch Assembly
Customer Repair Stories
Clothes washer would not spin with more than a couple socks in it. It would barely spin when empty.
Summary:
Get the washer on its back - unplugged!
remove wire(s) Harness from motor
remove water pump
unbolt 3 bolts holding the gearbox
slide gearbox and motor out as one piece ( a bit heavy)
remove and replace clutch assembly (pay attention to how things are removed)
Done! put it all back together... hope that helps. It worked perfect for me.. and m
-
Shawn from Longmont, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
spin cycle did not engage
-
Andrew from SLC, UT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set
This part goes on the agitator retaining bolt.
Replacing your Whirlpool Washer Washer
Customer Repair Stories
agitator broke
-
Joseph from Kalkaska, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
This upper agitator is an OEM part for your washing machine. It works with the rets fo the agitator assembly to spin clothing during the wash cycle. Make sure the power source to the washer is shut off before beginning this repair. To complete this repair you will need a ratchet and 7/16ths inch socket. To gain access to this part you will simply need to remove the detergent dispenser and barrier cap.
Customer Repair Stories
Top section of agitator was worn out
-
Vincent from Anaheim, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
This switch (Lid Switch Assembly With Leads, Washer Lid Switch, Lid Switch Assembly, Washer Lid Switch) tells the washing machine that the lid is closed, which allows the wash cycle to begin. The lid switch mounts to the underside of the cabinet top panel. The plastic on the actuator can become brittle with age and break when the lid is closed roughly. It can also break from the movement of an unbalanced load causing parts of the washer to strike it. This part must be replaced if it is broken and no longer being activated by closing the lid (indicated by the washer not agitating properly, or the machine not detecting the lid is closed). This switch is black plastic with wire leads. It is sold individually.
Replacing your Whirlpool Washer Lid Switch
Customer Repair Stories
lid switch failure
-
David from BREEDING, KY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
The washer would fill with water and wash,but would not drain and spinn out .
-
Susie from BRANDON, MS
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
This is used in your direct drive washer that has a neutral drain.
Replacing your Whirlpool Washer Gearcase
Customer Repair Stories
The spin gear was striped.
-
Aaron from Lake Mills, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Socket set
The washer wouldn't spin or agitate.
-
david from Monroe, MI
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Use this dispenser for your direct drive washing machine.
Replacing your Whirlpool Washer Fabric Softener Dispenser
Customer Repair Stories
Washer model didn't come with softener dispenser
-
Liz from Winchester, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
No fabric softener dispenser
-
Dennis from Port Orchard, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This is only the base, or the lower half of the agitator.
Replacing your Whirlpool Washer Bottom Agitator
Customer Repair Stories
Bottom agitator stripped
Excellent standard shipment time
-
Therese from Cobb, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
would not move clothes
.
-
phillip from worcester, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Sold individually.
This part is for large capacity belt drive and direct drive appliances.
Replacing your Kenmore Washer Drive Block - 2 5/16 Inch High
Customer Repair Stories
No spin on spin cycle
-
Thomas from Port Jervis, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench (Adjustable)
Loud Banging Sound At The End Of Spin Cycle
-
John from Hawley, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
This kit comes with springs, hardware, and brake lining.
Customer Repair Stories
Washmachine wouldn't spindry
-
Chuck from South Holland, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
Spin cycle stopped working
-
Brent from Highlands Ranch, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
This part is used to activate the lid switch when the lid opens/closes.
Replacing your Whirlpool Washer Lid Strike
This is a 2-speed drive motor for your washing machine. The motor rotates the spin basket when the washing machine is in spin or tumbling mode. You will likely need to replace the motor if you are experiencing burning smells or your washer will not start. The tools you will need to make this repair include a number two Phillips screwdriver, a flat-blade screwdriver, and a 5/16 nut driver.
Replacing your Whirlpool Washer 2-Speed Drive Motor - 60Hz 120V
Customer Repair Stories
washer motor burned out
(unplug the washer)
2. remove the screws on the back of the control panel to lift the control panel out of the way.
3. use a flat head screwdriver to remove the clips that hold the cabinet to the back panel.
4. disconnect the lid switch from the control ... Read more panel by removing the clip that connects them at the top of the cabinet.
5. tilt the cabinet forward to remove it.
6. use a flat head screw driver to remove the two clips that hold the water pump to the motor and swing the water pump out of the way.
7. use a nut driver to remove the shipping screw that holds the clips on to the motor.
8. disconnect the wiring harness from the motor
9. remove the two clips from the motor with a flat head screwdriver and remove the motor
remove the three prong coupler and rubber gasket from the old motor and put them on the shaft of the new motor
10. remove the 4 rubber pads from the old motor and slide them onto the new motor.
11. insert the new motor into the washer aligning the prongs of the coupler.
12 reassemble the washer in reverse order of disassembly
(the shipping screw does not need to be reinserted into the spring clip that holds the motor)
-
Joseph from SANFORD, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
I smelled smoke and then it quit working
-
Paul from Lakewood, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
This kit is used for direct drive washing machines and is found inside the gearcase.
Customer Repair Stories
Washer would try to agitate during spin cycle.
-
Lorin from Arlee, MT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Right hand threaded nut holds the tub in place in direct drive, top loading washing machines. To remove the spanner nut you will need a spanner wrench.
Sold Individually.