Models > FGHD2433KF1 > Symptoms > Will not fill with water

Parts That Fix Frigidaire Dishwasher FGHD2433KF1 Will not fill with water

Will not fill with water is a commonly reported symptom for the FGHD2433KF1 Frigidaire Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FGHD2433KF1 Frigidaire Dishwasher that will fix Will not fill with water. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

Fixes Symptom 90% of time
★★★★★
★★★★★
43 Reviews

Rated by 29 customers 

  

Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, you have a defective inlet valve that will need to be replaced.

$ 57.03
  In Stock
PartSelect Number PS1990907
Manufacturer Part Number 154637401

Replacing your Frigidaire Dishwasher Water Inlet Valve - 120V 60Hz

Replacing your Water Inlet Valve - 120V 60Hz

Customer Repair Stories

No water to dishwasher on any cycle

Unplugged dishwasher, pulled it out. Unclamped hose and unscrewed water source to inlet valve, removed wiring harness, unscrewed bracket and reinstalled new valve. Now have a functioning dishwasher.
  • David from Las Cruces, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
41 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Leak in the water inlet valve/solinoid

1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical connection to new valve solinoid.
6. Remounted assembly to the frame.
7. Re-attached the inlet water hose to the hose adapter connection on the valve.
8. Turned on the water, washed some dishes.
  • Mickey from Ooltewah, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
154 of 169 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 8% of time
★★★★★
★★★★★
2 Reviews

Rated by 1 customer 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

Water that fills your dishwasher lifts the float. When it reaches a certain level, the float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher.

$ 64.00
  In Stock
PartSelect Number PS3492842
Manufacturer Part Number 154773201

Replacing your Frigidaire Dishwasher Float Switch

Replacing your Float Switch

Customer Repair Stories

machine was not filling

First, I unplugged the dishwasher. After removing the under counter mounting screws, I pulled the dishwasher out from the cabinets. Because the switch is hard to reach, I put the dishwasher on its side (very carefully). Make sure to drain the dishwasher first, or it will leak all over your kitchen. To remove the switch, I unscrewed the single black screw in the middle of the switch and unplugged the electrical wires. I put the new switch in its place, screwed in the screw, and plugged in the electrical connection. I set the dishwasher upright, and ran it through a cycle before reinstalling it into the cabinet. I had previously tried replacing the water inlet valve, but that was not the problem.
  • jon from northampton, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!

No water to dish washer

After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
  • steve from virginia beach, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
35 of 64 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 FLOAT
Fixes Symptom 2% of time

Rated by 1 customer 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

As water is filling your dishwasher, a float rises along with it. When the float reaches a predetermined level, it shuts off the flow of water, thereby preventing a leak.

$ 23.56
  In Stock
PartSelect Number PS11770486
Manufacturer Part Number 5304506520

Replacing your Frigidaire Dishwasher FLOAT

Replacing your FLOAT

Customer Repair Stories

was brocken

just replace
  • Aleksandr from West Palm Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
8 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!