Parts That Fix General Electric Range C2S980SEM1SS Will Not Start
Will Not Start is a commonly reported symptom for the C2S980SEM1SS General Electric Range, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your C2S980SEM1SS General Electric Range that will fix Will Not Start. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
The top burner spark electrode, also known as a range surface burner igniter, is designed for use in your gas range. The function of this part is to provide the spark that lights the surface burner. If your gas range will not start, or if the igniter glows but will not light, you may need to replace the top burner spark electrode. This part is sold individually. This product is white in color and measures approximately 1-1/2-inches in length by 1/2-inch in width. Be sure to disconnect the gas supply to the range before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Customer Repair Stories
Change bad/broken igniter on gas stove top burners
-
James from Kaplan, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
burner would not lite
-
Glen from Kenner, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
The bake element is located on the bottom of the oven. If your oven will not heat properly it may be due to a faulty or damaged baking element. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats evenly. If the element is not heating evenly, or if it is not heating at all, it will need to be replaced. This element is 19 inches wide x 19 inches long, and has male spade push on terminals.
Replacing your General Electric Range Bake Element - Push On Terminals - 240V
Customer Repair Stories
Broken heating element
2)remove 2 bolts holding heating element
3)pull element out of the back of the oven about 8" so that the wire connects is visable
4)pull wire clips off of heating element and remove element from the oven
5)put wire clips on the new heating element
6)push new heating element back into the ... Read more holes in the back of the oven
7)screw botls back into the oven holding the heating element in place
8)Turn power back on
-
Paul from anna, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Lower bake Element would not heat.
-
Ronald from Nassau, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
Sold individually.
Customer Repair Stories
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
-
Dana from LEEDS, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Pliers
Customer Repair Stories
Part does not look like the part that needs to be replaced
-
P from FULLERTON, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
One burner would not light from spark. All other burners lite with spark.
Then watch a bunch of videos and found this gal to be the most he ... Read more lpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
-
Thomas from DEARBORN, MI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Customer Repair Stories
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
-
Brian from DOVER, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
terminal block melted
-
jonathan from willow springs, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
This burner head, or surface burner, is used in ranges and ovens. The burner sends gas through the holes and slots to create an equal flame across the cooking area. If the gas igniter glows but will not light up, or there are heating inconsistencies, replacing the burner head could be the solution to your problem. No tools are required for this installation. To change the burner, first lift the grate and take the burner cap off. Next, lift the burner away from the cooktop. To set the new burner in place correctly, check the locating tab that fits into the V-shaped notch and make sure the igniter fits into the cut-out. Refer to the diagram provided by the manufacturer for further instructions.
Replacing your General Electric Range Burner Head - Medium - 9500
Customer Repair Stories
Burner on stove not working correctly
-
Trevor from Eldersburg, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Burnt burner
-
Janine from Wind Gap, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Customer Repair Stories
The electrode had broke
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am ... Read more very happy.
-
O.Robert from Montrose, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Failed ignighter
-
Connie from WESTFIELD, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
This also comes with Spark Electrode.
This is a replacement vision burner or surface burner head for your gas range. It is silver in color and approximately 4.5 inches in diameter. This burner is sold individually. The burner head distributes gas to create an even flame across the cooking area. If you notice that your food is not cooking evenly, or you are not getting an evenly distributed flame, you may need to replace the burner. The burner is located beneath the burner cap, below the grate. To remove the burner, simply remove the grate and the burner cap, then lift the burner head out. Replace it with the new burner, and reinstall the cap and grate. This is an OEM part sourced directly from the manufacturer.
Customer Repair Stories
Gas burner wasn’t burning properly
-
Karin from ARUNDEL, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
-
Dan from WARROAD, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver