Models
>
ZBD6900G00SS
ZBD6900G00SS General Electric Dishwasher - Overview
Sections of the ZBD6900G00SS
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve
PartSelect #: PS259369
Manufacturer #: WD15X10004
May look different than the original, but will function the same.
$89.07
In Stock
Rear Basket Insert
PartSelect #: PS651723
Manufacturer #: WD28X10084
Sold individually.
No Longer Available
Upper Dishrack Wheel
PartSelect #: PS259051
Manufacturer #: WD12X10032
This wheel is sold individually. It comes with an attached axle.
No Longer Available
Front Basket Insert
PartSelect #: PS651724
Manufacturer #: WD28X10085
Sold individually.
No Longer Available
Door Seal
PartSelect #: PS651625
Manufacturer #: WD01X10120
It provides a seal between the tub and the door.
No Longer Available
Fold Down Clips - Set of 2
PartSelect #: PS258069
Manufacturer #: WD01X10046
These clips are sold in a pair. They are used in conjunction with the front and rear inserts for the lower dishrack.
No Longer Available
Questions And Answers for ZBD6900G00SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ZBD6900G00SS
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water inlet valve leaking
I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish wash
... Read more
er, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.
Read less
Parts Used:
-
Brad from wadsworth, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set, Wrench set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wire racks had rust on them
they clip right into the lower rack. takes two minutes
Parts Used:
-
David from Collierville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water wouldn't drain out of dishwasher
I had pulled out the dishwasher. Pump was on the bottom. One screw and a clamp, pump was off. It went back together with ease. I am women.
Parts Used:
-
Nicolette from Birmingham, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!