The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. If the fuse ...
The heating element (Flat Can Heating Element 5400W, Heating Element, Whirlpool Dryer Heating Element, Dryer Heating Element) provides heat to the dryer. It is metal and measures 10.5 inches long, 7.5...
The thermal cut-off (Dryer Thermal Cut-Off Fuse Kit, Dryer Thermal Cut-Off Kit) prevents the dryer from overheating when the dryer high limit thermostat fails in a closed circuit condition. This part ...
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt att...
This replacement door catch is for your dryer door. If the catch is broken and the door will not stay shut, the dryer may not turn on. Use a putty knife to pop out the existing door catch by the locki...
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is l...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
July 5, 2021
Makes a squealing noise from time to time
For model number WED6200SW1
Hello John, Thank you for the question. Normally this is an indication the Roller Wheels, Idler or belt will need to be replaced. We suggest ordering the Maintenance Kit. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. We hope this helps!
I turn the power on my dryer and it’s not working it keeps lighting up sensing what does that mean
For model number WED6200SW1
Hi Donald, Thank you for your inquiry. Although usually your control board can be the culprit for something like that. You should test the Thermal Fuse in your appliance. Sometimes that can be the cause of your machine stuck in the sensing mode. To test your fuse, you will need a multi-meter. First unplug your appliance and remove the fuse. Set the multi-meter on the lowest setting. The calibrate the needle until it lands on zero. Then you take the two probes and place them on the prongs of your fuse. If the needle stays on zero, then your part will need to be replaced. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
John
February 13, 2020
To help someone else: Issue was display would light up when powered on but would not run when pressed start and only make click sound without error code. Did diagnostic (3 sec pressing, 3x off/on, any button but power, start or pause) and received f25. Checked ohm on thermal fuse wp3392519, it was 1.25m ohms but should be close to 0. Was told by sears that f25 was thermistor wp8577274. Replaced both and it works.
For model number WED6200SW1
Hello John, thank you for sharing your experience. We are glad to hear your repair went well.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Danny
May 8, 2023
my dryer is squeaking when drying sometimes not all the time
For model number WED6200SW1
Hi Danny, thank you for the question. We have found that if the drive belt becomes loose, it wraps around the outside of the dryer drum and can cause squeaking. We would recommend checking the drive belt, part number PS11746376, to fix the issue. We hope this helps, good luck with this repair!
Ordered thermal cutoff kit for dryer , part # 279816 , but the high limit thermostat in kit is not correct. High limit for my dryer , part # 8577891 , has more wires. Is there a cutoff kit for my dryer? If not , how can i get only the thermal cutoff without buying a whole kit? Thanks
For model number WED6200SW1
Hi Brian,
Thank you for your question. There is a thermal cut-off kit for your dryer. The part number listed under your model number for the thermal cut-off kit is PS334299. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils. Not knowing what the problem was I started looking at the coils and could not see any broken parts. So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of
... Read moreneedle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading. I replaced with a new one and put it all back together the way I took it apart. Then I plugged it in and it worked first time, I now have warm dry clothes.
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi
... Read moreth an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back
... Read more off.