Models
>
TC607X0
TC607X0 Jenn-Air Trash Compactor - Overview
Sections of the TC607X0
[Viewing 6 of 6]
Manuals & Care Guides for TC607X0
Click to downloadKeep searches simple, eg. "belt" or "pump".
Off-Switch Actuator Kit
PartSelect #: PS3489806
Manufacturer #: W10342596
This kit contains everything you will need to replace your faulty off-switch actuator, including: normally closed switch, toe guard, template, 2 screws, and actuator. If your trash compactor keeps run...
$99.27
In Stock
15 Inch Compactor Bags - 15 Pack
PartSelect #: PS1964579
Manufacturer #: W10165295RP
Trash compactor bags are a practical way to discard your waste. Due to the extreme pressure of the compactor, trash compactor bags designed to handle the force are necessary. These bags are made from ...
$26.44
In Stock
Drive Gear Kit
PartSelect #: PS398589
Manufacturer #: 882699
This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop...
$49.23
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
15" Paper Compactor Bags - 12 Pack
PartSelect #: PS382653
Manufacturer #: 675186
Moisture-resistant liner. Pre-cuffed.
No Longer Available
Foot, Front - Single
PartSelect #: PS11747965
Manufacturer #: WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is imp...
$7.45
In Stock
15" Compactor Bag Carrier with Easy Grip Handles
PartSelect #: PS1782408
Manufacturer #: 13030RP
This 15 inch compactor bag carrier fits around the compactor bag inside the compactor and is used to easily lift and remove trash compactor bags once they are full. Simply place the reusable bag carri...
$35.91
In Stock
Directional Switch
PartSelect #: PS11744742
Manufacturer #: WP777811
The function of the directional switch on your trash compactor is to ensure the ram lowers to compress your trash, then returns to the top position. If your trash compactor does not complete this task...
$64.14
In Stock
Charcoal Filter
PartSelect #: PS11742279
Manufacturer #: WP4151750
This part is sold individually. The filter is black in color and measures approximately 4-1/2 inches wide by 4-1/2 inches high. This part is for your trash compactor. This part acts as a filter and de...
$19.59
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Door Shelf
PartSelect #: PS11739017
Manufacturer #: WP2177962K
This door shelf is made for your refrigerator, and prevents anything you have stored in the refrigerator door from falling out when the door opens and closes. It is made of white plastic and is sold i...
$48.48
In Stock
Hinge Bracket
PartSelect #: PS11739061
Manufacturer #: WP2183805
This hinge bracket, also known as a door stop, is attached to the bottom of the door and is used to limit how far the door swings out to protect the refrigerator itself, and any surrounding cabinets f...
$10.73
In Stock
Questions And Answers for TC607X0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the TC607X0
[Viewing 8 of 8]Compactor ram gets stuck
Fixed by
these parts
these parts
Show All
Doesn’t stop at end of compacting cycle
Fixed by
these parts
these parts
Show All
Won’t start
Fixed by
these parts
these parts
Show All
Door won’t open or close
Fixed by
these parts
these parts
Show All
Drawer is hard to open and or close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Light not working
Fixed by
these parts
these parts
Show All
Won’t stay on
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Beware the "two screws, five minutes" repair stories!
Needed a replacement actuator for KitchenAid trash compactor model KUCS03FTSS0. The part that broke is a small metal flange held in place by two screws. PartSelect.com clearly shows this part in the online exploded view of Container Parts. When I received the replacement order in the mail, I was surprised that it was not what I thought
... Read more
I had ordered (a single replacement piece), but a new, *completely redesigned* actuator kit. For this model (and perhaps for other models) this new kit requires much more extensive work than just replacing two screws. Repair entailed removing the trash compactor from its installation position, removing the recess cover and machine front, disconnecting and removing the old actuator switch, drilling holes in the machine front, attaching the new actuator assembly, and disconnecting and reattaching the foot pedal. Not an overly burdensome or complicated repair, but I had been fooled by the expectation of it being a five-minute job! (Submitted on 7/2/2011 by Scott - Ventura, CA)
Read less
Parts Used:
-
Scott from Ventura, CA
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
166 of 173 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Compactor stuck in lower position
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.
... Read more
r />Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Read less
Parts Used:
-
Asbjorn from The Woodlands, TX
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
67 of 82 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
Read less
Parts Used:
-
Scott from Indianapolis, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
41 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!