The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w...
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th...
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place...
This multi rib belt spins the dryer drum during the drying cycle. This belt is 91-5/8 inches in length, 3/8th of an inch wide and has five ridges. It is black in color and made of rubber. You may need...
This is a replacement lint filter for your dryer. The lint filter is approximately 12 1/2 inches in length. Simply remove the existing filter and replace it with the new one. Check for an excess build...
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
The idler pulley tightens the drive belt to properly spin the dryer drum. It is attached to an idler bracket. This part comes with the idler pulley and center bearing. To replace this part, you will n...
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough ...
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi...
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
$32.34
In Stock
Questions And Answers for MDG5500AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Andy
December 16, 2019
Everything okay, but no heat air.
For model number MDG5500AWW
Hi Andy,
Thank you for your question. If the dryer is not heating correctly, there are some parts that you will need to check to see which one is causing the issue. Here is a link from our website that you may reference on what parts to check, https://www.partselect.com/AdvancedModelSymptoms.aspx?ModelNum=MDG5500AWW&mfgModelNum=&fkMfgID=1&ModelMasterID=7777&PID=19. We hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Steven
September 18, 2022
Panel lights go on but buttons do not respond
For model number MDG5500AWW
Hi Steven,
Thank you for your question. If the buttons on the control panel do not respond, the issue is either with the control panel or the electronic control board. You will need to test the ribbon cable on the control panel for continuity with a multimeter to see if it is working correctly. If the control panel is fine, check the electronic control board. If there is corrosion where the ribbon cable attaches to the electronic control board, then the electronic control board will need to be replaced. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Need a diagram of the dryer so i can locate the front panel and how to remove it so i can inspect the tumbler belt.
For model number MDG5500AWW
Hello and thank you for writing.
Belt PS11741110 is in the list of compatible parts for your model. We hope this helps. Please contact us anytime if you require further assistance. For your convenience, we have attached the link to our repair video. We hope this helps. Good luck with your repair.
https://www.youtube.com/watch?v=z76qrBmSUeE&feature=emb_title
I'm on propane. When the start button is pressed, there is a hum, but desn't start. Today, there was a burning smell. I am assuming it is the motor. Is this correct and not repairable and need to purchase a new dryer, or not? Thanks
For model number MDG5500AWW
Hello Dave, thank you for contacting us. We have researched the model, and it seems like the issue might be with the drive motor, part number PS3500892. Over time, the motor windings may get weak or damaged, causing it to not generate enough power to rotate the drum. You may check the motor for burned out windings to verify the fault. The drive motor is replaceable and you may not have to purchase a new dryer. We hope this information helps!
Dryer has lights on control panal but will not start,checked out all safty fuses and all checked good.cannot change any settings on display changed out control board and still got the same problem.What em I missing?
For model number MDG5500AWW
Hello Danny, thank you for the great question. Unfortunately, you just have a failed touchpad. If unplugging the dryer for 60 seconds did not reset the electronics, you will need to order and replace the touch control panel, part number PS2036215, to fix this problem. Thank you for your inquiry, good luck with this repair!
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are
... Read more located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.