This filter is made of metal and is intended for use with ranges and cooktops. Grease filters are an important but often neglected part of ranges. If the filter is full, your extractor fan will become...
This bake element is for the bottom of your oven. The bake element supplies heat for baking. If you find there is little to no heat when baking, a burned out bake element, or food is taking too long t...
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of...
This is a leveling leg for your oven, range, or stove. The leveling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This surface burner switch, also known as an infinite switch, controls and regulates the heat output of the burners on a stovetop. The user simply adjusts the knob on the user interface panel, which i...
This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware inside of your appli...
The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Before making any repai...
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness...
This part is a replacement halogen lamp for your oven. The bulb is 25 watts and 120 volts. If your light bulb is burned out, this is the part that replaces it. Be sure to turn off power to your range ...
This cartridge assembly male contact spade is made of metal. These are sold individually, though each range uses four contact spades.
$13.95
In Stock
Questions And Answers for JES9860AAB
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kenneth
January 26, 2020
F1-8 code beeping. I had a repairman come out from trinity home repair 2 weeks ago and i have not heard from him. What do i need???
For model number JES9860AAB
Hello and thank you for writing.
F1-8 - A button on the touchpad PS11744103 is either stuck or short-circuited. So you would need to check and possibly replace the touchpad. We hope this helps. Please contact us anytime if you require further assistance.
How do i take the touchpad ps11744103 off?? i see 2 screws, one on each side.
For model number JES9860AAB
Hello Kenneth, thank you for your question. Here is an installation story from another customer that might help!
Remove knobs and loosen the two screws for each switch.
Open oven door and place a rack at the highest level. Place a thick phone book on the rack and place a thick folded towel on top of it. This is to act as a protected table when removing and installing the new part.
Remove philips head screws from end covers and from angle bracket and stove. Leave screw nuts and angle bracket attached to old part for now.
Remove old part from stove by lifting up slightly then place on protected rack.
Slide lamp housing from red plastic lens and remove and store the red plastic lens for reuse.
Remove ribbon cable from circuit board. Remove fasheners from circuit board. Remove switches.
Remove old part and remove mounting bracket.
Re-install mounting bracket on new part and reinstall components in reverse order.
Verify that all connections are intact before mounting assembly to stove.
Good luck with your repair!
Was this helpful?
Thank you for voting!
Demmy
August 27, 2023
Getting Fault Code F1-1 on Jenn-Air electric downdraft range. Fault Symptom: While the oven is supposed to be off the top element is heating the oven until a certain temperature is reached then fault code F1-1 appears.
For model number JES9860AAB
Hi Demmy, thank you for reaching out. Based on our research, this error code indicates an issue with the temperature sensor, part number PS1570174. You may need to do a continuity test of this part first, if it is faulty then you may need to replace it. Let us know if you have further questions!
I need drip pans under the burners for the jen air stove
For model number JES9860AAB
Hello Frances, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the Cartridge the elements are part of. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the
... Read more new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts.
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read morereinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.