Models
>
HDB821-05
HDB821-05 Hotpoint Dishwasher - Overview
Sections of the HDB821-05
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Silverware Basket (Grey)
PartSelect #: PS261346
Manufacturer #: WD28X265
The silverware basket, used for dishwashers, is in the bottom of the dishrack. The basket is used to hold eating utensils such as spoons, forks, and knives. If the basket is worn out or broken, you sh...
$91.04
In Stock
Rinse Aid Fill Cap
PartSelect #: PS2351824
Manufacturer #: WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
$18.37
In Stock
Motor and Pump Kit
PartSelect #: PS260801
Manufacturer #: WD26X10013
This is a pump and motor kit for your dishwasher. This assembly replaces many old-style pump and motor kits that were manufactured since 1970. The instructions are included with this kit in to assist ...
$249.86
In Stock
Water Inlet Valve
PartSelect #: PS259411
Manufacturer #: WD15X93
This water inlet valve is specially designed for those dishwashers that fit under the counter from 1974 To Present. The valve should be located behind the lower kickplate panel in either the right or ...
$57.50
In Stock
Impeller and Seal Kit
PartSelect #: PS259598
Manufacturer #: WD19X10032
The impeller and seal kit is used in a dishwasher. The kit includes all the parts needed to do this repair, including the impeller, seal, blade, filter, skidder and skidder holder. If your washer is l...
No Longer Available
Drain Solenoid Repair Kit
PartSelect #: PS260462
Manufacturer #: WD21X802
This kit includes the armature and link assembly. You may need the solenoid bracket which is sold separately.
This valve opens in order for the water to drain out of the dishwasher.
$84.05
In Stock
Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$15.89
In Stock
Fine Thread Telescoping Tower Power
PartSelect #: PS260569
Manufacturer #: WD22X120
This telescoping power tower comes in three sections.
$28.12
Special Order
Dishwasher Tub Insulating Blanket
PartSelect #: PS958842
Manufacturer #: WD01X10262
No Longer Available
Questions And Answers for HDB821-05
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the HDB821-05
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Insufficient fill water, dishes not getting clean (valve diaphram had ruptured)
1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to g ... Read more ain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to g ... Read more ain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
Read less
Parts Used:
-
Don from Mount Vernon, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
71 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Basket was lost
Opened package from Parts Select.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.
Parts Used:
-
Joseph from Elmendorf, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
49 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor was getting noisier every time we used the dishwasher. We knew it was just a matter of time before it totally quit.
The most difficult part was removing the dishwasher from below the counter. Once that was complete, I simply turned the washer onto it's front surface to access the pump easier. Simply disconnected the electrical connectors, loosened the three hose clamps holding the hoses to the pump. Lastly removed a stiff arm bracket holding the pum
... Read more
p. Reversed the order to install the new one using a longer bracket provided with the new unit. Hooked up the electrical connections last and slid the washer back in place. The washer runs like new now and is not making noise. The replacement part was a perfect match.
Read less
Parts Used:
-
Glenn from Clemmons, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
48 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!