Models
>
FEC36C4ASD
FEC36C4ASD Frigidaire Cooktop - Overview
Sections of the FEC36C4ASD
[Viewing 4 of 4]Manuals & Care Guides for FEC36C4ASD
Click to downloadInstall
Installation Instructions
(1.69MB)
Manual
Owner's Manuals
(1.49MB)
Wiring
Wiring Diagram
(0.14MB)
Keep searches simple, eg. "belt" or "pump".
Drip Bowl - 8"
PartSelect #: PS437595
Manufacturer #: 316048413
This chrome drip bowl is designed for use with electric cooktops and ranges. This drip bowl is sold individually. At the widest point this part has a diameter of approximately 10 inches. It sits benea...
$12.59
In Stock
Chrome Drip Bowl - 6"
PartSelect #: PS437596
Manufacturer #: 316048414
The drip bowl catches grease and spills that come from cooking on your stove top. They are located under the heating elements. Drip bowls are often neglected and can become rusted and cracked. If your...
$7.46
In Stock
Terminal Block Kit
PartSelect #: PS470125
Manufacturer #: 5303935058
This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If y...
$16.24
In Stock
Single Control Knob
PartSelect #: PS648840
Manufacturer #: 318196633
This is only 1 knob and is sold individually.
$56.95
In Stock
Red Indicator Light Lens
PartSelect #: PS2349641
Manufacturer #: 318250801
This indicator light lens protects bulbs in ranges, ovens, stoves, and humidifiers. The lens keeps the bulb from getting cracked, scratched, and damaged. It is 1 inch long and 1 inch wide. If your len...
No Longer Available
Surface Burner Coil Element - 8" - 2100W
PartSelect #: PS473948
Manufacturer #: 5308011964
$152.66
In Stock
Questions And Answers for FEC36C4ASD
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the FEC36C4ASD
[Viewing 3 of 3]Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old pans/bowls were corroded
Very easy---simply unplug the burners, remove the old pans and replace with the new ones
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
Parts Used:
-
John from Nisswa, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
48 of 53 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would consistantly go to high no matter where the dial was positioned.
First I unplugged the stove.Removed the upper control panel back (10 phillips screws). Removed the plastic dial( pulls straight off). Removed the 2 screws behind the dial that is holding the switch in the control panel. Took one wire at a time off the old switch and put them on the new switch according to each electrical spade marking. L1
... Read more
, L2, H1, H2 and P. Installed the new switch in the control panel securing it with the 2 screws. Installed the dial, installed the upper back panel using the old screws. Plugged the stove back in and tested it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it.
Read less
Parts Used:
-
Gary from Herrick, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
32 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
corroded terminals
was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
Parts Used:
-
Gary from hollywood, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
22 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!