The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w...
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th...
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place...
This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses ...
This lint filter is a genuine OEM replacement filter for your dryer. Replacing it is easy as it just slides in like your normal filter. Make sure to check the filter slot for excess buildup of lint, a...
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough ...
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi...
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
$13.45
In Stock
Questions And Answers for DG303
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mary
March 1, 2023
what type of glue/adhesive do you use to replace the felt seal on the dryer drum.
For model number DG303
Hello Mary, thank you for the question. According to our research, it is a good idea to use a high-temperature adhesive, part number PS11757492, while replacing the felt drum seal, part number PS11740771. This adhesive is designed to hold objects together, and will not disintegrate at a high temperature. We hope this helps!
I have had success finding and buying your parts in the past, but stumped by this one. Had this dryer for decades, and it still does a good job drying clothes, but won’t turn off on its own. It will keep running long after clothes are fully dry regardless of setting. If you turn initial dial setting to a point near off, it will complete the cooldown. There’s no option for just timed dry with heat only “Air Fluff”.. There must be a moisture or dryness sensor gone bad somewhere. I have seen one in diagrams, but it doesn’t match my unit. Any suggestions or referrals would be appreciated.
For model number DG303
Hello Tom, thank you for reaching out to PartSelect. Make sure your lint screen is clean. If the vent is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time. To ensure proper dryer performance, you should clean your dryer’s venting system at least once per year. If no vent hose and inner clogs are found, then the cycling thermostat, part number PS11757518, is most probably faulty or damaged. The cycling thermostat advances the timer when the heat turns off as its drying. We hope this sorts out your problem!
I have a Maytag dg303 dryer and it works perfectly fine except when it stops at the end of the cycle, the buzzer does not turn off. No problems starting/stopping/heating. The only problem is the buzzer fails to shut off at the end of each drying cycle! Help!
For model number DG303
Hello, Thank you for your question. I would look into replacing the buzzer itself. That is PartSelect Number: PS11743788. We hope this helps.
Was this helpful?
Thank you for voting!
Shinichi
May 17, 2023
The dryer fires up, but quit in a minute.
For model number DG303
Hello Shinichi, thank you for your inquiry. Based on our understanding of the issue, we suggest you check the high-limit thermostat. If defective, replace the high-limit thermostat, part number PS11740646, to fix the issue. We hope this sorts out your problem!
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of t
... Read morehe front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job. Thank you.
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through
... Read more. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.