Models
>
DECIDL1
DECIDL1 Frigidaire Dryer - Overview
Sections of the DECIDL1
[Viewing 7 of 7]Keep searches simple, eg. "belt" or "pump".
Door Latch Kit
PartSelect #: PS475419
Manufacturer #: 5366021400
The door latch is designed to keep your dryer door closed, even during the drying cycle. If your dryer door will not stay closed, the drying cycle might not start, or it could stop suddenly. If you no...
$50.56
In Stock
M Series Ignition Coil Kit
PartSelect #: PS470049
Manufacturer #: 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the ...
$21.45
In Stock
Main Terminal Block Kit
PartSelect #: PS471605
Manufacturer #: 5304409888
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches...
$9.37
In Stock
Flame Sensor
PartSelect #: PS459818
Manufacturer #: 5303281135
This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off eno...
$28.57
In Stock
Igniter
PartSelect #: PS900236
Manufacturer #: 5303937186
The burner igniter is used in dryers and activates or lights the gas burner to heat the dryer during a cycle. *Please note: Do not handle this igniter by the gray part, because it is fragile. If your ...
$59.49
In Stock
Power Resistor
PartSelect #: PS975867
Manufacturer #: 134446800
This part helps the timer advance while in the Automatic Dry cycle.
$52.07
Special Order
THERMOSTAT
PartSelect #: PS418429
Manufacturer #: 131658100
This thermostat heater assembly is used for dryers and is attached to the operating thermostat. The function of this part is to automatically regulate temperature and make sure the dryer does not over...
$66.11
In Stock
Questions And Answers for DECIDL1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DECIDL1
[Viewing 8 of 8]Door won’t close
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils we
... Read more
re easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
Read less
Parts Used:
-
Brett from Monticello, MN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
95 of 108 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Catch broke, door wouldn't stay closed.
Used a screwdriver to pop out broken piece. Used pliers to snap in new one.
Parts Used:
-
Dianne from Kansas City, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
72 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read more
d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read less
Parts Used:
-
Timothy from Spring Valley, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
95 of 148 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!