Models
>
BA5910
BA5910 Maytag Washer - Overview
Sections of the BA5910
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Heat Resistant Adhesive
PartSelect #: PS11728058
Manufacturer #: W10841140
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising th...
$23.85
In Stock
Transmission Lower Lip Seal Repair Kit
PartSelect #: PS2017479
Manufacturer #: 207843
This transmission lip seal repair kit comes in two pieces: a red four inch long piece, and a black one inch long piece. Both pieces are made entirely of plastic. This repair kit comes with and instruc...
$23.92
In Stock
Agitator Shaft Spring
PartSelect #: PS11738926
Manufacturer #: WP215581
Sold individually.
$9.76
In Stock
Orbital Transmission Kit - Deep Tub
PartSelect #: PS2347239
Manufacturer #: 6-2097750
With this kit the mounting stem and seal is included.
No Longer Available
Questions And Answers for BA5910
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the BA5910
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Floor floded when washer started.
Thirty year old Maytag washer. Remove two screws at bottom of front panel with Philips screw driver. Hinge panel up to disconnect front panel from top of machine. Tilt washer back against wall to gain access to pulley at underside of washer. Then remove Philips head screw from bottom of center shaft. Remove bevel washer with screw. Remove
... Read more
stop block from end of center shaft and wind the pulley off center shaft. Clean center shaft of any debris and lightly coat with grease. Install belt on new pulley and motor, wind new pulley on center shaft. Replace stop block, washer, screw, and front cover.
Read less
Parts Used:
-
Keith from Big Sur, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
9 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oil leak from lower lip seal
I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and
... Read more
added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.
Read less
Parts Used:
-
Anthony from CHESANING, MI
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
now i know the problem, it was the transmission.
well i first put on 2 new belts because they were worn and smoking. the new belts did not fix the problem. you suggested putting in a new pulley. it went against my better judgement that the pulley was defective. well i put in the new pulley and now the real problem has surfaced. the transmission is not working. now i want to orde
... Read more
r a new tranny and low and behold it is no longer available. well why did you sell me a $99 pulley when that was not the next part to change after the belts were replaced. now i have a new pulley on a washer that is going to the recycle center as metal trash. well on my part i will reward maytag by buying a ge washer now. plus i will not count on using you as my parts supplier.
Read less
Parts Used:
-
stephen from E NORTHPORT, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!