Models
>
AW26L3ASK
AW26L3ASK Admiral Washer - Overview
Sections of the AW26L3ASK
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Drive Belt - 51 inches long
PartSelect #: PS11738882
Manufacturer #: WP21352320
This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suf...
$10.98
In Stock
Drain Pump with Pulley
PartSelect #: PS11741799
Manufacturer #: WP35-6465
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is ac...
$84.63
In Stock
Snubber Ring
PartSelect #: PS11738845
Manufacturer #: WP21002026
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome ass...
$13.11
In Stock
Transmission Pulley and Bearing Kit
PartSelect #: PS2003651
Manufacturer #: 12002213
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race was...
$69.83
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.76
In Stock
Screw
PartSelect #: PS11742755
Manufacturer #: WP489483
This screw is sold individually.
$13.09
In Stock
Screw
PartSelect #: PS11740978
Manufacturer #: WP3196164
This screw is sold individually.
$7.68
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Leveling Leg and Pad
PartSelect #: PS2026623
Manufacturer #: 25001119
This part includes locknut.
No Longer Available
Screw with Washer
PartSelect #: PS11752524
Manufacturer #: WPW10309247
Sold individually.
$29.99
Special Order
Questions And Answers for AW26L3ASK
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AW26L3ASK
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
Parts Used:
-
David from Boca Raton, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench set
560 of 570 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Load Grinding/Rubbing Noise in Rinse and Spin Cycles
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using
... Read more
a screwdriver to pry the front of the top up off the front panel on both sides then hinge it back out of the way. Use a nut driver to remove the two screws on the inside edge of the front panel and remove the front panel. Once the front panel is off you will see the water pump on the right hand side as you face the front of the machine. Remove the hose clamp on the water pump with the flat head screw driver or nut driver and use a pair of pliers to remove the compression clip on the water pump. Remove the 4 bolts holding the water pump in place. Reverse the entire process to put it back together. This job was very easy and I was only without a washer for 2 days because of partselect.com.
Read less
Parts Used:
-
Doug from Port Richey, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
139 of 151 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would agitate, pump, but not spin
First I unplugged it, then removed the agitator and tub assemblies, then I tipped it back and removed the belt and pully and thrust bearings. After reading on here I learned the brake would stick and after installing the thrust bearing kit I found out I couldnt fit in the shims. That led me to believe the brake was siezed inplace so i cou
... Read more
ldn't fit in the parts. I removed the thrust bearing kit and removed the transmission assembley. I took apart the brake and found the two pieces had siezed together, after I got them apart I sanded both peices and lubed the shaft with high temp silicone like you would use on a cars brake system. I put the brake back together, BE VERY CAREFUL THE SPRING HAS ALOT OF PRESSURE! I then put the transmission back in, reinstalled the thrust bearing kit and it fit great. I put in the tub and agitator and washed clothes.
Read less
Parts Used:
-
steve from lebanon, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
60 of 72 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!