Kenmore Washer Dryer Combo Parts

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Kenmore Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Kenmore Washer Dryer Combo Parts

Videos!
Agitator Directional Cogs – Part Number: 80040
Your Price
$4.40
   In Stock
Kenmore Washer Dryer Combo Agitator Directional Cogs
★★★★★
★★★★★
356 Reviews
PartSelect Number PS388034
Manufacturer Part Number 80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what prevent the agitator from rotating in both directions, while allowing it to rotate in one direction. Your agitator cogs may be malfunctioning if you can manually rotate the agitator in both directions. If broken they will need to be replaced. Cogs can be found by simply removing the softener dispenser and then removing the agitator cap. The are attached to the agitator. This replacement part features 4 agitator directional cogs. There are 4 cogs per package that are made up of high-quality plastic. This part comes in white/beige.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Marks left on clothes
  • Not cleaning dishes properly
  • See more...
Installation Instructions
mike from Kent, WA
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair. Read more...
Videos!
Dryer Drum Support Roller – Part Number: WPW10314173
Your Price
$22.73
   In Stock
Kenmore Washer Dryer Combo Dryer Drum Support Roller
★★★★★
★★★★★
38 Reviews
PartSelect Number PS11752609
Manufacturer Part Number WPW10314173
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the drum roller only and does not include the tri-rings. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.
Fixes these symptoms
Installation Instructions
Jeff from Phoenix, AZ
noisy and slow drum speed
1. disconnect power,gas and vent lines
2. pop off top of unit
3. remove front of dryer
4. lay unit on its back
5. remove drum and replace pulley assembly,belt,drum rollers of which it has 2 rear and 2 front
6. reverse above and then remove filter-vent housing and scrape off old seal install new seal
7. re-connect power,gas and vent use again
8. only sad part to whole job was seeing how cheaply whirlpool now makes thier products Read more...
DRYER BEARING SLIDE 2-PACK – Part Number: WE03X37320
Your Price
$15.16
   In Stock
Kenmore Washer Dryer Combo DRYER BEARING SLIDE 2-PACK
★★★★★
★★★★★
3 Reviews
PartSelect Number PS17626249
Manufacturer Part Number WE03X37320
This OEM replacement dryer slide bearing is white in color, and approximately 3 inches long. The slide bearings are supportive linings for your dryer. If they have eroded, or are damaged, the drums will scrape against metal during the drying cycle which will produce a squealing, or scraping sound.
Fixes these symptoms
Installation Instructions
mike from SUMMERVILLE, SC
Dryer was making increasingly loud "thumping" sound.
Parts were shipped quickly, packaged correctly, and were in original GM packages - very reassuring. BTW, your customer service is excellent.
Reviewed YouTube videos.
Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics from PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them.
Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector.
When reinstalling, re-tighten those connectors.
Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!! Read more...
Videos!
Drum Glide Bearing - White (Sold individually) – Part Number: WE3M51
Your Price
$13.20
   In Stock
Kenmore Washer Dryer Combo Drum Glide Bearing - White (Sold individually)
★★★★★
★★★★★
9 Reviews
PartSelect Number PS4704230
Manufacturer Part Number WE3M51
This drum glide bearing is an authentic OEM replacement part that is compatible with dryers. It is white in color and made of highly durable plastic. The bearing allows the drum to rotate smoothly and dry your clothes thoroughly and evenly. It keeps the drum stable and protects it from excessive friction damage. Over time, the bearing may wear down or break due to normal aging or wear from repeated use. If the bearing is no longer able to support the drum, you will likely notice unusually loud grinding or squeaking noises from the dryer. You may also notice increased drying times due to poor drum rotation. Inspect all the bearings on your dryer, as they tend to wear down at the same time. Each drum glide bearing is sold individually.
Fixes these symptoms
Installation Instructions
Maurice from MINERAL SPGS, AR
Dryer was making noise
Took the top and front end of the dryer off. Took the old slider spacers off and installed the new ones. I replaced all four of them even though only two was bad. While I had the dryer open I decided to use my shop vac to clean up the lint that had accumulated there. Replaced the front and the lid plugged it up, hit the start no noise just like new. Read more...
Videos!
Multi Rib Belt – Part Number: 661570
Your Price
$21.99
   In Stock
Kenmore Washer Dryer Combo Multi Rib Belt
★★★★★
★★★★★
49 Reviews
PartSelect Number PS382430
Manufacturer Part Number 661570
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium" difficulty to install. Refer to your model number and user manual to ensure this part is correct for you. To complete this repair you will need a Phillips screwdriver, 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Ensure you disconnect your power to the dryer before beginning this repair, which should take between 30 and 60 minutes maximum to complete.
Fixes these symptoms
Installation Instructions
Lucas from Nuevo, CA
Need it a new pulley and belt
I did the repair all by my self and just payed for the parts. Read more...
Videos!
Idler Pulley – Part Number: 279640
Your Price
$27.00
   In Stock
Kenmore Washer Dryer Combo Idler Pulley
★★★★★
★★★★★
117 Reviews
PartSelect Number PS334244
Manufacturer Part Number 279640
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If damaged or broken the dryer will not dry properly, will not tumble properly, or may not even start. Installation is rated as "Medium" difficulty. This part is located on the dryer drum, around the tension pulley. Refer to your user manual and model number for repair instructions and to ensure this part is right for you. For this repair project, the tools needed are a Phillips screwdriver, 1/4 inch nut driver, putty knife, small flat blade screw driver, and needle nose pliers.
Fixes these symptoms
Installation Instructions
eric from Boulder, CO
Belt Wheel was broken at axle. Terrible noise.
Removed the top and back of dryer with screw socket. It was quite easy. Then, I removed the broken wheel by releasing the tension spring. I replaced the wheel. The toughest part was re-threading the belt. But, even that was simple. The dryer runs smoothly and quietly again! Read more...
Videos!
Direct Drive Motor Coupling – Part Number: 285753A
Your Price
$27.92
   In Stock
Kenmore Washer Dryer Combo Direct Drive Motor Coupling
★★★★★
★★★★★
160 Reviews
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
Push-to-Start Switch – Part Number: WE4M416
Your Price
$18.23
   In Stock
Kenmore Washer Dryer Combo Push-to-Start Switch
★★★★★
★★★★★
26 Reviews
PartSelect Number PS3487190
Manufacturer Part Number WE4M416
This switch is used to activate the dryer.
Fixes these symptoms
  • Touchpad does not respond
  • Will Not Start
  • Won’t Start
  • See more...
Installation Instructions
Gary from LAVALLETTE, NJ
replaced start button and start switch
disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working Read more...
Videos!
Clutch Assembly – Part Number: 285785
Your Price
$27.63
   In Stock
Kenmore Washer Dryer Combo Clutch Assembly
★★★★★
★★★★★
78 Reviews
PartSelect Number PS334641
Manufacturer Part Number 285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining is worn out, the clutch assembly will not rotate properly to release the brake. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate there is an issue with your clutch. If the washer spins when the washer basket is empty but not when it’s full, or if the assembly begins to turn blue, you may need to replace the clutch assembly. This assembly includes a brake cam driver, blue springs for large capacity washers, a black spring for compact washers, and the installation instructions. It’s constructed of plastic and metal, and comes in beige/silver.
Fixes these symptoms
  • Burning smell
  • Spinning Issues
  • Spins slowly
  • See more...
Installation Instructions
Andrew from SLC, UT
spin cycle did not engage
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase mounting bolts and took the entire gearcase, shaft, motor, etc... together, out from under the washtub. the clutch slides off the gearshaft with a little fidgeting and the new assembly is easily installed where the previous was. put everything back together... then... spin spin! worked perfectly Read more...
Door Handle – Part Number: WE01X30378
Your Price
$71.04
   In Stock
Kenmore Washer Dryer Combo Door Handle
★★★★★
★★★★★
20 Reviews
PartSelect Number PS12743305
Manufacturer Part Number WE01X30378
This is a door handle made for use with dryers. This door handle is made of solid white plastic and allows you to open and close the door of the dryer. If your current dryer door handle is broken or missing, it will need to be replaced. This handle measures 9 inches long and 2 inches thick and attaches at its top and base. To replace this handle, simply pry off its left side and pull it off, and then insert the prongs on the right side into the door and push it in place. This OEM door handle is sold on its own and does not come with any other accessories.
Fixes these symptoms
Installation Instructions
TERESA from IRONDALE, AL
dryer handle broke off
once the part arrived, it was a perfect fit and just snapped on! DONE! Read more...

Kenmore Washer Dryer Combo Appliance Types

Back to Top

Related Kenmore Washer Dryer Combo Parts

Back to Top

Popular Kenmore Washer Dryer Combo Models

Below are the most popular Kenmore Washer Dryer Combo models we have. Enter your model number in the search box to find your model.

Need Help Finding Your Model Number?
View More
Back to Top