Parts That Fix Maytag Dishwasher MDB8969SDM0 Not draining
Not draining is a commonly reported symptom for the MDB8969SDM0 Maytag Dishwasher, and we have put together a full guide on how to fix this.
This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your MDB8969SDM0 Maytag Dishwasher that will fix Not draining.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Ratings submitted by customers like you who bought this part.
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
$92.13
In Stock
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
Replacing your Whirlpool Dishwasher Dishwasher Drain Pump
Customer Repair Stories
Water not draining from the dishwasher
I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video
Frederick from BIG PRAIRIE, OH
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
11 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Ratings submitted by customers like you who bought this part.
This drain hose is 6 and 1/2 feet.
$31.66
In Stock
PartSelect Number PS2358130
Manufacturer Part Number 8269144A
Replacing your KitchenAid Dishwasher Drain Hose
Customer Repair Stories
Drain hose leaking
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
Robert from Beaufort, SC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
7 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unwanted water.
A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wren
... Read morech). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.
Ratings submitted by customers like you who bought this part.
Measures level of soil in the water.
$33.79
In Stock
PartSelect Number PS11757214
Manufacturer Part Number WPW10705575
Replacing your KitchenAid Dishwasher Turbidity Sensor
Customer Repair Stories
Failed diagonistics test for OWI sensor
Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls
... Read more out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.
Read less
Mark from Lancaster, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
59 of 84 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
