This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This is a drive belt for various models of dryer. This belt is responsible for allowing the drive motor to rotate the dryer drum. Over time and with use, this belt will wear out and if it becomes dama...
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Randy
November 26, 2023
How do you take the white agitator part to bolt?
For model number GTW465ASN3WW
Hello Randy, thank you for asking. We are providing you with the instructions that will help you in removing the auger from the agitator.
1- Remove the fabric softener dispenser.
2- Now align the raised bump with the opening on the auger.
3- Use the screwdriver to puncture through the inner shaft of the auger.
4- Twist clockwise until the auger releases and lifts it out.
5- Now you will have access to the bolt that holds the lower agitator.
We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Debra
January 5, 2024
I am experiencing excessive noise and vibration during spin cycle.
For model number GTW465ASN3WW
Hi Debra, thank you for reaching out. Make sure you are not overloading the washer, your washer is levelled, and the drain pump is clean. If all checks are fine, we would recommend replacing the suspension rod, part number PS12343380. We hope this sorts out your problem!
Hello.,. Tub drains by itself leaking from somewhere.. I left water in it and it all drained out,..,I tipped over and it seems wet in the middle from behind belt cover. After looking at the diagrams there is no tub seal.,. Where else can it be leaking from?.,.I'm guessing the drain pump seal? But I would assume that water would be over near the drain pump and not in the center.,., please help so I can buy the right part.,., please and thank you.,.
For model number GTW465ASN3WW
Hi Brian, thank you for the question. Based on the description you have provided, we would recommend checking the drain pump, part number PS12723115. You may need to replace it to fix the issue. We hope that helps!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Turn off hot and cold water supply valves feeding washer. Disconnect both water hoses from washing machine. Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve. Slightly lift the bottom portion of metal plate and slide to release hooks for
... Read moreeasy removal. Pull back and tilt forward plastic control panel to get it out of your way. Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is. Remove two screws from water inlet valve. (one on each side) Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful. Once you have disconnect the sensor you can remove the water inlet valve. If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve. The new valve DOES NOT come with a replacement O-ring so you will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole. Don't forget to install the O-ring or your washer WILL leak! Put everything back together in reverse order. Check hose connections for leaks. Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.