Magic Chef Range Valves

Your Price

$51.05

Magic Chef Range Pilot with Thermocouple

★★★★★

11 Reviews

PartSelect Number PS11750349

Manufacturer Part Number WPW10206112

The pilot stays lit all the time and, when the oven is turned on, the flame gets bigger and surrounds the thermocouple. When the thermocouple senses the required heat, the safety valve opens to let the gas flow to the oven burner tube where the pilot flame ignites the gas.

Fixes these symptoms

Gas igniter glows, but will not light
Little to no heat when baking
Will Not Start
See more...

Installation Instructions

Peter J from Brooklyn, NY

Pilot Light Won't Stay Lit

First I removed the oven door by pulling straight up off of the hinges in the open postion. Next remove oven racks,then use 1/4 nutdriver to remove back screws on inside oven bottom plate. Next remove gold nut on silver tube @ pilot connection,then remove 1/4 nuts that hold pilot assembly. Next open top of stove and remove small gold nut "with the thin wire from pilot"attached to the back left of oven control knob. Snake that nut and wire from the top of the stove down to the oven and removethe whole pilot assembly. To install carefully unroll the new pilot assembly starting from the oven "there are two round holes you need to snake the tube into"and up behind the back & into the stove top. Make your connection@ the oven assembly. Next attach the assembly with the 1/4 screws that you removed,then make your connection"gold screw silver tube" now push in your oven control knob to alllow gas to flow to the pilot tube and check for leaks with a water @ soap solution. No bubbles no leaks. Light your pilot . . . . You must hold in the oven knob. Put back in oven plate,,,, 1/4 screws,,,,racks close the stove top ,put door back on hinges and your done. . . . . Hope I helped,. . Pete Read more...

Your Price

$49.31

Magic Chef Range Burner Cap - Black

★★★★★

4 Reviews

PartSelect Number PS11747514

Manufacturer Part Number WP98017461

Sold individually.

Installation Instructions

George from CASTROVILLE, CA

parts missing on a used stove

put in place Read more...

Your Price

$53.87

Magic Chef Range Burner, Top

PartSelect Number PS11747518

Manufacturer Part Number WP98017537

Sold individually.

Installation Instructions

George from CASTROVILLE, CA

parts missing on a used stove

put in place Read more...

Your Price

$107.44

Magic Chef Range Burner Control Valve with Igniter

★★★★★

3 Reviews

PartSelect Number PS2080913

Manufacturer Part Number 74002413

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Randall from Rochester, NY

igniter would no longer work, it would stick

pull knob off streight out. remove two phillips head screws, disconnect wire to disassemble. To reassemble reattatch wire to replacement igniter, screw in two phillips head screws and push on the knob. Read more...

Your Price

$101.41

Magic Chef Range Burner Tube - Right Front

PartSelect Number PS11747519

Manufacturer Part Number WP98017582

Also called Venturi Tube.

Fixes these symptoms

Gas smell
See more...

Your Price

$83.34

Magic Chef Range Oven Burner Pilot with Thermal Couple

★★★★★

1 Review

PartSelect Number PS2087252

Manufacturer Part Number 74009852

Fixes these symptoms

Will Not Start
See more...

Your Price

$59.11

Magic Chef Range LP Spud Kit (For Use With LP)

PartSelect Number PS11748021

Manufacturer Part Number WPW10032010

Your Price

$248.53

Magic Chef Range Gas Valve - 60Hz

★★★★★

1 Review

PartSelect Number PS11747502

Manufacturer Part Number WP98014893

This part makes sure that no gas is released until the igniter gets enough power to ignite the gas range.

Fixes these symptoms

Gas igniter glows, but will not light
See more...

Your Price

$118.00

Magic Chef Range Burner Valve - LF, RF, RR, Liner OR lower

PartSelect Number PS11748993

Manufacturer Part Number WPW10141709

Sold individually.

Installation Instructions

John from PRINCETON, IN

Oven would not maintain temperature and LR burner would not turn on

Oven temperature sensor was very easy to replace - just need a Philips screw driver.
Gas manifold valve for burner was a little awkward but not hard to do - I used pliers to undo because I didn't have a wrench to fit. It all went fine. Read more...