Kenmore Washer Dryer Combo Agitators

Videos!

Your Price

$4.40

Kenmore Washer Dryer Combo Agitator Directional Cogs

★★★★★

356 Reviews

PartSelect Number PS388034

Manufacturer Part Number 80040

This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what prevent the agitator from rotating in both directions, while allowing it to rotate in one direction. Your agitator cogs may be malfunctioning if you can manually rotate the agitator in both directions. If broken they will need to be replaced. Cogs can be found by simply removing the softener dispenser and then removing the agitator cap. The are attached to the agitator. This replacement part features 4 agitator directional cogs. There are 4 cogs per package that are made up of high-quality plastic. This part comes in white/beige.

Fixes these symptoms

Does not dispense fabric softener or detergent
Marks left on clothes
Not cleaning dishes properly
See more...

Installation Instructions

mike from Kent, WA

washer wouldn't agitate

First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair. Read more...

Your Price

$133.90

Kenmore Washer Dryer Combo Dual Action Agitator

★★★★★

4 Reviews

PartSelect Number PS418275

Manufacturer Part Number 131605901

Fixes these symptoms

Will not agitate
See more...

Installation Instructions

BRIAN from UPLAND, CA

Clicking due to agitator dogs slipping

One bolt (after removing the fabric softener dispenser and a water tight cover you will see it). Remove the bolt and slide it straight up and then it's the reverse to put in the new one. Very simple repair and very inexpensive if you willing to do it yourself. Read more...

Your Price

$15.13

Kenmore Washer Dryer Combo Agitator Cam Kit

★★★★★

4 Reviews

PartSelect Number PS334624

Manufacturer Part Number 285751

This agitator cam kit contains an almost three inch white retainer and four agitator dog ears. This kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover).

Fixes these symptoms

Will not agitate
See more...

Installation Instructions

Nathaniel from Kennesaw, GA

Top half of agitator didn't agitate

First I removed the fabric softener container and set it aside. Below that, there is a plastic cover with a rubber gasket that distributes the fabric softener. I also just pulled that out and set it aside. Below that was an 11mm bolt that attached the upper and lower agitator to the drive mechanisim. The lower agitator is attached directly to the shaft and that was working properly so I knew it was't a motor or drive issue. Until it broke, the top half of the agitator sat still for a second, then it turned clockwise with the lower agitator. This helped push the clothes down to the lower part to be circulated throughout the wash cycle. Well, now the upper agitator just sat there, like it wasn't attached to anything at all. Below the aforementioned plastic cover with the rubber gasket, I found a part that had 4 plastic "teeth" that moved in and out, releasing and grabbing the inside of the upper agitator, respectively. Over time, these teeth wore down and stopped "grabbing" the ridges on the inner part of the upper agitator, causing it to stop turning with the lower agitator. I removed the 11mm bolt and tried to seperate the upper agitator from the lower agitator to replace the teeth. This part was kind of tough to get out because the plastic clips that held it in were deformed. I just had to pull hard and eventually it came apart. In the process, I broke two of the clips. I wasn't really concerned because the 11mm bolt holds everything in place anyway. After that I just swapped out the worn teeth with the new ones. I put it back together in the opposide order I took it apart and viola....good as new. And it only cost me $15 bucks. Read more...

Your Price

$101.23

Kenmore Washer Dryer Combo Agitator

★★★★★

1 Review

PartSelect Number PS446533

Manufacturer Part Number 3204401

This is an agitator that is compatible within various makes and models of washer, and is used to move, or agitate, the clothes and soap/water mixture around within the tub of the washer. This agitator is made of a high-quality white plastic and is installed down the center of the main washer tub. This agitator requires a cap and seal on its top to fasten and secure it within the washer, but is sold as an individual agitator. If you notice your clothes are not being cleaned or are covered in soap residue, it is likely that the agitator base is stripped or broken, leading to the agitator being unable to rotate and move properly. It is recommended that when you remove the agitator, you inspect the directional cogs, also known as dogs, or whatever hardware is attached to the base of the agitator, like the trunnion, for any damage or wear, since those parts are commonly replaced when agitators stop working properly. Replacing this agitator is as simple as removing its cap and seal, which will allow you to remove the agitator and replace it.

Fixes these symptoms

Will not agitate
See more...

Installation Instructions

Kyle from Maricopa, AZ

The Agitator

The top of the agitator broke off so the washing machine was no longer spinning the agitator. Took the nut off the top of the agitator and there was a steel sleeve inside that had to come out of the agitator and be put into the new agitator so it would sit correctly on the "tower" and spin. It took me awhile to get the sleeve out of the old agitator but once I did it slipped right into the new agitator and then the new agitator bolted right onto the "tower". It only cost me $40.00 for a new part so I'm sure I saved myself around 100 dollars or more by doing it myself. Read more...

Your Price

$63.50

Kenmore Washer Dryer Combo Agitator Drive Block

★★★★★

1 Review

PartSelect Number PS1152574

Manufacturer Part Number 134418700

The agitator drive block rotates the agitator assembly in your washer. If the drive block breaks down due to wear and tear the agitator will stop working. If you notice that your washer is making loud noises while washing, this may indicate an issue with the agitator block. You will find this part underneath the dispenser cover and cup. You will need a 1/2-inch socket to remove the agitator bolt and then simply lift off the agitator (this may require some effort to lift off). Use a flat-head screwdriver to remove the old drive block, push the new one into place with firmness. This part is made of metal and measures about 2 inches long and 1 inch wide.

Fixes these symptoms

Will not agitate
See more...

Installation Instructions

James from Somerville, MA

Agitator Drive Block wore out

Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.

Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.

Very happy camper here! Read more...