Kenmore Ice Maker Ice Makers

Kenmore Ice Maker Replacement

★★★★★

★★★★★

220 Reviews

This ice maker (Complete Icemaker Assembly, Whirlpool Icemaker Kit, Ice Maker Assembly, Refrigerator Ice Maker, Icemaker) receives water from the water inlet valve, freezes it, and dispenses it into the ice bucket until the bucket is full. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage, and water quality. You can perform a voltage test with a multimeter or perform an inlet valve test. If you’re unable to make ice, or notice leaks then it may be a sign your ice maker is damaged and could be in need of a replacement. This model measures approximately 11x5 inches, is constructed of plastic and metal, and comes in black/silver. This ice maker is a complete assembly; the whole assembly attaches to the wall of your freezer.

Kenmore Ice Maker

★★★★★

★★★★★

77 Reviews

This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.

Kenmore Ice Maker Bin Temperature Sensor

★★★★★

★★★★★

14 Reviews

This bin temperature sensor is for ice makers. The bin temperature sensor monitors the temperature in the ice maker bin and sends the temperature reading to the electronic control board. Disconnect the power before installing this part. Wear work gloves to protect your hands.

Kenmore Ice Maker Ice Cutter Grid Complete Assembly

★★★★★

★★★★★

10 Reviews

If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker and contains thin, heated wires that slice the ice into cubes that are then deposited in the ice bin. If the cutter grid is broken, ice can back up within the ice maker. This part is sold as a complete assembly and is used with freestanding ice makers. Be sure to wear work gloves to protect your hands when completing this repair. This is an OEM part that sources directly from the manufacturer.

Kenmore Ice Maker Ice Bucket - White

★★★★★

★★★★★

12 Reviews

The ice bucket in your freezer collects the ice from the ice maker and stores it. If your old ice bucket is damaged you may want to replace it as it can leak. This product is made of white plastic and is approximately 13 inches in length and 9 inches wide at the widest point. This is an OEM part sourced directly from the manufacturer. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the damaged bucket, making sure to collect any broken pieces. Then, simply slide the new bucket in place.

Kenmore Ice Maker Icemaker Control Assembly

★★★★★

★★★★★

26 Reviews

The “Icemaker Control Assembly” (Module & Motor Assembly, Ice Maker Control Module, Icemaker Module, Refrigerator Ice Maker Module) is what controls the actions of your ice maker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions such as the heater, water inlet valve, the cube size, and cube ejection. If your ice maker control is broken it can no longer properly control the ice maker functions. It may not produce any ice, make small ice cubes, or have intermittent operation. This can occur due to normal wear and tear. The icemaker control assembly is attached to the ice maker mold, and is under the white cover. Test the icemaker control assembly by using a multimeter. If this reveals the assembly to be defective, you will need to replace this part. It is approximately 4.25 inches square, beige, and is constructed of plastic and metal. This replacement part features one icemaker control assembly, including the control module and the motor.

Kenmore Ice Maker Water Fill Cup and Bearing

★★★★★

★★★★★

10 Reviews

This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, or not making/dispensing ice. If you notice the fill cup has been damaged or cracked; replace the part straight away. This water fill cup is a genuine OEM part and will fit most refrigerators, but check the list of compatible brands to make sure yours is included before purchasing.

Kenmore Ice Maker Ice Mold

★★★★★

★★★★★

13 Reviews

This is an ice maker mold and heater assembly for a refrigerator ice maker. It is used with modular style icemakers and is located in the freezer section of the refrigerator. This ice mold is flake resistant which prevents the coating on the mold from flaking into the ice cubes when the ice mold begins to wear. The ice mold forms the ice cubes and the heater allows the ice cubes to fall from the ice mold to drop them into the ice bucket. You will need to remove the ice maker from the refrigerator to access the mold and heater assembly. This is a genuine replacement part.

Kenmore Ice Maker Front Cover

★★★★★

★★★★★

2 Reviews

Kenmore Ice Maker Shut Off Arm

★★★★★

★★★★★

3 Reviews

This is a shut off arm for the ice maker in a refrigerator. When the shut off arm has reached maximum height, it triggers the switch to shut off the ice maker so it does not continue to make ice until the level of ice in the ice bucket begins to drop. The ice maker can also be shut off by lifting the shut off arm past the maximum height and into the locked position. This part is made of metal, and measures approximately 9 inches wide and 4 inches tall. This is an OEM replacement part.