Inglis Range Elements and Burners

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Inglis Appliance Parts
Shop By Part Type

Popular Inglis Range Elements and Burners

Videos!
Your Price
$67.25
  In Stock
Inglis Range Oven Bake Element
★★★★★
★★★★★
74 Reviews
PartSelect Number PS11752501
Manufacturer Part Number WPW10308477
This bake element is located at the bottom of the oven to supply heat and it has push-on terminals. If your baking element is burnt out, the heat is not consistent, or is defective, then replacing the element could be a solution to your appliance problem. The tools needed for this replacement are: a screwdriver and needle-nose pliers. The first step in is to unplug the range or shut off the house circuit breaker before starting. Unscrew the black of the oven cavity to pull out wires from the defective element. Reconnect wires to the new element and screw it back on. Make sure the element is sitting flat.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven is too hot
  • See more...
Installation Instructions
Esther from San Antonio, TX
heating element burnt up
first I pulled the stove from the wall. Then unplugged the stove from the wall (electric stove) for safety. then I removed the middle back panel screws(2) and then the panel. I then pulled the wires off the heating element that was bad. I took the screws (2) off the heating element inside the oven. I had to use WD-40 to loosen the screws because with the heat they were really stuck. I removed the heating element and replaced it with the one I got through partselect.com. Put everything back and walla finished. Partselect.com sent me the right part at the right price and fast. No hassles at all. Read more...
Videos!
Your Price
$30.21
  In Stock
Inglis Range Standard Y-Frame Surface Burner
★★★★★
★★★★★
11 Reviews
PartSelect Number PS11743366
Manufacturer Part Number WP660532
The standard y-frame surface burner provides heat to your range. If you notice that your element will not heat, you may need to replace your surface burner. This product is 6 inches in diameter, and 1500W. The manufacturer suggests replacing the receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy, and you will not need any tools. To complete the repair, simply lift out the old burner and replace it with the new one. Check that the burners are turned off before you begin this repair.
Fixes these symptoms
Installation Instructions
Laurie from Tequesta, FL
Burner element broke and drip bowls needed to be replaced.
I went to the local discount mart and bought drip bowls. The ones available at that store did not fit, so I decided to buy directly from the stove's manufacturer distributor.

The drip pans were simple to replace, as was the new burner element. My old one had broke and was still working, but I decided to replace it when I ordered the drip pans.

Everything was easy to install and it looks like a brand new new stove top! I saved a lot of money doing it myself. Read more...
Videos!
Your Price
$38.18
  In Stock
Inglis Range Receptacle Kit
★★★★★
★★★★★
11 Reviews
PartSelect Number PS389217
Manufacturer Part Number 814399
This assembly of parts is a surface burner receptacle kit, and is used in conjunction with your range. The assembly comes with two wires, two wire nuts, two pieces of heat-shrink tubing, and the receptacle. If your element is not heating, you may need to replace your surface burner receptacle. The function of this part is to connect the surface element to the wire harness. The tools you will need for this installment include a number two square-head screwdriver or a number two Phillips screwdriver, a pair of wire strippers and crimpers, and a heat gun.
Fixes these symptoms
Installation Instructions
Tim from Pittsford, NY
Stove would not heat up
Cut old wires to receptacle, striped the wires, wire nutted to new receptacle, screwed new receptacle into stove and installed heating element.

Piece of cake, but then again my degree is in electrical engineering so I should be able to handle a couple of wire nuts. Read more...
Videos!
Your Price
$136.60
  In Stock
Inglis Range Broil Element
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11731333
Manufacturer Part Number W10856603
This broil element supplies heat for cooking purposes and is located in the roof of an oven. If you find there is little to no heat when cooking, a burned-out element, or food is taking too long to cook, these symptoms could be solved by replacing this part. Before starting this replacement, make sure you unplug the range from the power source or shut off from the house circuit breaker. All you need to complete this repair is a Phillips screwdriver. For safety reasons, make sure to wear gloves. Refer to the manual provided by the manufacturer for more instruction.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Installation Instructions
Ramona from Mexico, MO
The broiler element started sparking and melting in one spot. I thought it would catch on fire and quickly turned off the oven.
First we unplugged the range. My husband removed the old element using a screw driver. He also removed the back panel on the oven after pulling it out from the wall. He unplugged the broiler prongs and plugged in the new element, put it all back together using the screw driver. We plugged it back in, turned on the oven and it is working great! Simple and easy to do in a short amount of time. Cool!! Read more...
Videos!
Your Price
$134.61
  In Stock
Inglis Range Surface Element
★★★★★
★★★★★
12 Reviews
PartSelect Number PS11751367
Manufacturer Part Number WPW10259865
This is a surface element for the stove top on your range. It supplies heat to the top of the range cooking area. This model is 2100 watts and is eight inches in diameter. It has looped terminal ends, and five turns. The most common reason for needing to replace this part is if your current element is not retaining heat. The first step to this repair is to make sure the burner control is set to off, and that the element is cool to the touch.
Fixes these symptoms
Installation Instructions
Thomas from Longwood, FL
Stove heat was inconsistent and
After turning off the circuit breaker, I removed the elements and pans, raised the top and cut the wires to the receptacle assembly. Stripped the wires, slid on the shrink tubing and applied the wire nuts. I used a hair dryer rather than a match to shrink the tubing. Reinstalled the drip pans and inserted the elements. The instructions were clear and the project was easy. The stove works like new. Read more...
Videos!
Your Price
$220.74
  In Stock
Inglis Range Element with Limiter 6 Inch - 1200W
★★★★★
★★★★★
14 Reviews
PartSelect Number PS11764915
Manufacturer Part Number W10823711
This is a radiant surface element with limiter, and it works in conjunction with your range. The function of this part is to give heat to the surface directly above it, on cooking area stove top.This model is sold individually and is 1200 watts. The main reason for needing to replace this part is if your element will not heat. Before ordering, make sure to test your stove top radiant element for continuity to make sure it is the problem. To make this installation you will need a Phillips screwdriver, and a 14-inch nut driver.
Fixes these symptoms
Installation Instructions
Mark from Loxahatchee, FL
Right rear burner went bad
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip charge. It was easy!! Read more...
Videos!
Your Price
$230.28
  In Stock
Inglis Range Dual Surface Element - 2500w/1200w
★★★★★
★★★★★
10 Reviews
PartSelect Number PS11764902
Manufacturer Part Number W10823692
This is the replacement large surface element for your cooktop or range. It is approximately 10-inches in diameter and is 1200/2500 watts. The large surface element is installed under the cooktop and heats up the area directly above it. You will need to replace the element if it does not heat up properly. As you will be working around electricity, be sure that your range is disconnected from power before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
GEORGE from NEWNAN, GA
Radiant element, 2400 watt, under Ceran glass cok top needed replacement.
turned off power
removed ceran top from cabinet
removed element
installed new element
replaced top
powered up and was done Read more...
Videos!
Your Price
$220.40
  In Stock
Inglis Range Burner Element - Right Front
★★★★★
★★★★★
1 Review
PartSelect Number PS11764908
Manufacturer Part Number W10823698
This surface element is for ranges. The surface element supplies the heat to a cooking area on top of the range. Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
Installation Instructions
paul from trumbull, CT
No heat on burner
Turned off electricity! Pulled stove out -lifted up glass top(carefully) simply removed burned out coil and replaced it with new one. Read more...
Videos!
Your Price
$103.79
  In Stock
Inglis Range Surface Element - 6 Inch
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11751368
Manufacturer Part Number WPW10259868
This surface burner heating element is six inches in diameter. It has four turns and looped terminal ends. Sold individually.
Fixes these symptoms
Installation Instructions
judy from palatine, IL
i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it
just plugged it in! Read more...
Your Price
$103.52
  In Stock
Inglis Range Bake Element
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11747129
Manufacturer Part Number WP9752294
This heating element is found under the base of the oven.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven not heating evenly
  • See more...
Installation Instructions
Robert from Powell, OH
Hidden bake element burned out.
This heating element is accessed from the right side of the range. The parts drawings are misleading, making you think that it can be accessed from below -- not so!

Remove the right side panel from the range by removing screws on back edge, and bottom center on the inside. Slide the panel forward to release from tabs on the front edge, then pull out and off.

Separate the insulation that hides the terminals and access cover for the element., then remove one screw at the rear edge of this panel, and slide it toward the rear, then pull out.

Before disassembling the side, you can check to verify that the element is burned out by removing the rear panel and doing a continuity check on the wires leading to this element from the rear of the range. The wires on my range were a salmon or pink color with high temperature insulation. Read more...

Related Inglis Range Parts

Back to Top